Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Which radio mods are actually worth doing, and where does a modified rig stop being legal to use?

ci_cover.jpg

Modification threads tend to mix two separate questions: what improves a radio, and what you are allowed to do with it afterward. I'd like to take both, starting with a rough ranking by value and risk.

Low risk, often high value: power and grounding fixes, ferrites and common-mode chokes, a better speaker or mic, a clean firmware update from the manufacturer, and a proper fused DC supply. These rarely change the radio's RF behavior, but they often fix the problems people blame on the radio itself, such as hum, a noisy receiver, voltage sag on transmit, and thermal rollback.

Moderate risk: TCXO installs, added or swapped IF and roofing filters, cooling fans, and internal audio changes. They can be worthwhile, but they need care with soldering, shielding and alignment. A TCXO is the clearest example. A 1 ppm error is about 146 Hz at 146 MHz and about 440 Hz at 440 MHz. That matters for narrow digital modes, weak-signal work and tight channel spacing, and not much for casual FM voice.

Higher risk: expanded transmit range (the so-called MARS/CAP mod), third-party firmware on cheap handhelds, and anything that touches the final amplifier, ALC or deviation limits. Opening up the transmit range does not by itself authorize you to use those frequencies. MARS and CAP operation needs authorization from the program, and those programs have their own rules on equipment, programming and net procedures. Check your organization's communications policy before putting those channels in a radio, even if the hardware allows it.

Receive-side upgrades are a different matter. Expanded receive is mostly a convenience and a question of the radio's front-end selectivity. A wide-open handheld receiver with no preselection can be overloaded by nearby FM broadcast, paging or cellular transmitters. Opening up coverage can make the radio worse in a strong-signal environment unless you add a bandpass or notch filter. Local laws on what you may listen to also vary, so don't assume that anything you can tune is fair game.

A few questions to start with. What radio and band are you working on? What problem are you trying to fix: drift, desense, poor transmit audio, overheating, or battery life? And do you have a way to verify results, such as a dummy load, a wattmeter, a second receiver or an SDR to check for spurs? A mod that can't be measured is easy to get wrong without noticing.

  • Replies 2
  • Views 54
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the symptom before picking a mod. A lot of "my receiver is deaf" reports turn out to be local noise, not the radio. Switch-mode supplies, USB chargers, LED drivers, powerline adapters and badly shielded computer gear can all raise the noise floor. A battery-powered receiver away from the house wiring is a good test. If the noise disappears there, a filter inside the radio won't help. You need to find the source, then use ferrites, common-mode chokes on the DC and USB leads, better bonding, or a different supply.

On the power side, voltage drop is the usual culprit on transmit. A rig that behaves on the bench and sags in the car is often limited by thin wire, a poor fuse holder or a marginal connector. Size the cable for the full transmit current, put the fuse close to the battery, and measure voltage at the radio during a keyed transmission, not at idle. If you move to LiFePO4, check the charge voltage and the battery's low-voltage cutoff. Don't assume it's a drop-in replacement for lead-acid in every setup. Lithium packs should have protection circuitry, and you shouldn't bypass it to squeeze out more runtime.

For fans, a modest airflow improvement helps most on digital modes and other high-duty-cycle operation. Put the fan where it moves air across the heatsink, don't just stir the air in the enclosure, and watch for motor or PWM noise showing up on receive. A temperature-controlled fan is usually quieter in every sense than one that always runs.

On the TCXO, check whether your radio's reference stage and the replacement part are actually compatible. Frequency, output level and mounting all matter, and an incorrect reference can leave the radio worse than before. Re-check calibration afterward with a frequency counter or a known-accurate signal.

  • Moderators

On the legal side, keep three things apart: what the radio can do, what the license allows, and what the equipment rules say. In the US, amateur operators have more freedom to modify their own equipment than users of other services, but that freedom covers amateur-band use, not other services. Equipment for services such as FRS, GMRS, CB and business or public-safety channels is generally expected to be certified for that service, and modifying it can invalidate that status. Other countries have their own rules, so check your national regulator and don't assume the US approach applies.

For MARS, CAP and similar programs, the rule is simple: no authorization, no transmitting on those channels. A radio that can be unlocked is not an authorization. If you're a member, follow your program's guidance on approved radios, programming files and frequency use. If an organization has issued rules for its own equipment, a personal modification may not be acceptable even if it's technically fine.

Third-party firmware needs extra care because it can change power levels, deviation, filtering and transmit limits. Before using it on the air, check the output on a dummy load and a spectrum display or a second receiver. Look for harmonics, spurs, overdeviation and splatter. Back up the original configuration, confirm the exact model and hardware revision, use a stable power source during flashing, and be prepared for the radio to need recovery if the update fails.

For audio changes, don't turn up mic gain until the radio sounds loud. On FM, excess deviation causes distortion and adjacent-channel interference. On SSB, overdriving the audio chain or ALC causes splatter. Compare your transmit audio against a monitor receiver, and run a few test transmissions with a local operator who can give a report. A modified radio that sounds good to you but is splattering across the band is not an improvement.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.