Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field comms setup: what order do you build power, antenna, and noise control for an EMCOMM deployment?

ci_cover.jpg

I'd like to compare notes on the order of operations for a portable station, especially one that may be asked to run for many hours at a served-agency site. A lot of setup advice covers one piece, such as the antenna, the generator, or the battery. Most field problems come from how those pieces interact: a noisy charge controller on the 40 m noise floor, a long run of thin DC wire that sags on transmit, or a mast that gets raised before anyone checked where the overhead lines are.

Here is a rough sequence to argue with:

1. Site and safety first. Pick the antenna and mast location before the shelter, and check overhead power lines. Plan for a fall zone at least as large as the mast height with a good margin, not just the mast height. Put the generator downwind and well away from the tent, with the exhaust pointed away from people and a CO alarm in any occupied shelter.

2. Power plan with numbers. Estimate average current, not just peak. A 100 W HF rig can pull around 20 A on transmit, but with typical voice duty cycle and receive time the average may be a small fraction of that. Add a laptop, a VHF/UHF radio, lighting, and charging for handhelds. Battery energy in watt-hours is roughly amp-hours times 12.8 V for LiFePO4. Leave margin, and do not count on 100% of the rated capacity.

3. Distribution. Use a fused distribution block with Powerpole-style connectors, a fuse as close to the battery as practical, and wire sized for under about 0.3 V drop at full transmit current. LiFePO4 holds voltage well, but a BMS low-voltage cutoff can drop the station instantly, so a voltmeter on the bus is useful.

4. Antenna and feedline. Pick the antenna for the mission. NVIS-style horizontal wire for regional HF, a vertical or J-pole for local VHF/UHF, and so on. Add a common-mode choke at the feedpoint and another near the radio. Use low-loss coax on VHF/UHF runs, since thin RG-58 loses a lot at 2 m and 70 cm over long distances.

5. Noise baseline. Before turning on every accessory, note the noise floor on the bands you'll use. Then add loads one at a time: solar controller, inverter, laptop charger, LED lights, generator. Anything that raises the noise gets moved, filtered with ferrites, or replaced.

6. Documentation and teardown. Keep a communications log, record frequencies and net schedules, and use a teardown checklist that is the setup list in reverse. Antennas come down first if weather is turning.

Where does your sequence differ? Do you build power first, antenna first, or run parallel teams? And what noise sources have caught you off guard that a checklist could have flagged?

  • Replies 2
  • Views 52
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd put noise testing earlier than most checklists do, because it decides what you can keep on the power bus. MPPT solar controllers and cheap 12 V to USB or laptop adapters are common HF noise sources. A practical routine is to tune to a quiet spot on each band you plan to use, note the S-meter or SDR noise level with only the radio running, then switch on one accessory at a time. If a device raises the floor by an S-unit or more, try these fixes in order: a clamp-on ferrite on both the input and output leads (several turns through a suitable mix, not one pass), separating it from the antenna feedline, or powering it from a different branch. Sometimes the answer is to disconnect the solar controller while operating and let the panels recharge between sessions.

On generators, inverter models are quiet acoustically and usually friendlier to radio than old open-frame units, but they are not noise free. Keep the generator as far from the antenna as the cords reasonably allow, use a properly rated outdoor cord, run GFCI protection, and don't backfeed anything into building wiring. If the station is battery-based, a generator can be reserved for charging in a scheduled window instead of running through every net. That also reduces fuel use and CO risk.

One LiFePO4 note: most cells should not be charged below freezing unless the battery has low-temperature charge protection or a heater. For winter deployments, check the manufacturer's spec before assuming solar or a DC-DC charger will work at dawn.

  • Moderators

The mast and shelter side tends to cause the most avoidable mistakes because people treat them as an afterthought. A fiberglass push-up mast is fine for lighter wire antennas and small verticals, but it is only as good as its guying and base. Use non-conductive guy line, stake or ballast every guy point, and keep the load light at the top. Wind loads on a mast with a beam or a heavy coax run add up quickly. If a thunderstorm is approaching, the plan should be to disconnect coax from the radio, lower the antenna, and move people away from the mast. A short ground rod in the field is not lightning protection.

For coax runs, make a drip loop where the cable enters the tent or vehicle, and keep the feedline away from tent poles and metal stakes where it can be tripped on or chafed. Choke the line, label each cable end so teardown is quick, and avoid coiling excess coax tightly unless it's a deliberately made choke. Running the coax perpendicular to a horizontal wire for the first stretch helps avoid coupling to the radiating element.

For EMCOMM specifically, I'd add three checklist items that often get skipped: spare power and a second antenna option for the primary band, a printed copy of frequencies, net procedures, and forms (such as an ICS 309 communications log), and a handoff plan for operator rotation so one person isn't running the station for the entire shift. The best station design is the one a relief operator can sit down at and understand within a minute or two.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.