Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a from-scratch HF wire antenna: where the real compromises are (wire, choke, radials, modeling)

ci_cover.jpg

I'd like to collect notes on building antennas from raw materials instead of buying kits. This is a rough framework for a first multiband wire antenna plus a simple vertical. Please correct it, and add what you'd change.

Wire. For permanent dipoles, 14 AWG hard-drawn copper or copper-clad steel is the usual choice because it resists stretching. Stranded insulated 14 AWG works, but plain copper will sag over time on long spans. Thinner wire (18 to 22 AWG) is fine for portable use and low power, but it breaks more easily. Wire gauge has only a small effect on loss at HF. It affects mechanical life and slightly affects bandwidth and resonant length. Insulation shortens the resonant length by a few percent, so the usual 468/f(MHz) feet is only a starting point. Cut long and trim.

Supports. End insulators can be dogbones, PVC or polycarbonate. Ropes should be UV-resistant polyester or Dyneema-type line, not cheap nylon that stretches. At the center, strain relief matters more than people expect. The coax should not hang from the SO-239 or the wire junction. Use a bracket, or a loop of cable tied to the support.

Feedline and common-mode current. A half-wave dipole is balanced, but coax is not. Without a choke, the coax shield becomes part of the antenna. That distorts the pattern, can bring RF into the shack, and makes SWR readings depend on cable position. A 1:1 current balun at the feedpoint, or a choke of ferrite (mix 31 is common for HF) on the coax, addresses this. A coiled-coax choke is a cheaper alternative, but its bandwidth is narrower. For nonresonant doublets, 450-ohm window line to a tuner with a balun is a good option. Ladder line has low loss even with high SWR, but it wants to stay symmetrical and away from metal.

Verticals. A quarter-wave is roughly 234/f(MHz) feet, trimmed in place. The ground system matters more than the radiator. Elevated resonant radials, two to four of them sloping down, are a practical choice. Ground-mounted verticals need many more radials to reduce loss. Fiberglass poles make good non-conductive supports, but check that a pole is actually fiberglass. Many fishing poles are carbon fiber, which conducts and can detune the wire. It is also a hazard near power lines.

Modeling and measuring. EZNEC (NEC-based) and MMANA-GAL (MININEC-based) are both useful for relative comparisons: height, inverted-V angle, radial count. Check segmentation, ground type, and wire diameter. Treat absolute gain numbers with caution. For measurement, an antenna analyzer gives R and X, not just SWR. The lowest SWR point isn't always resonance, and a reading taken without a choke may change if you touch or move the coax.

Questions for the thread: Are trap antennas worth building at home, or are fan and linked dipoles more reliable? And what's your preferred method for checking whether the choke is working?

  • Replies 2
  • Views 51
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On traps, the main trade-off is loss and weatherproofing against convenience. A trap is a parallel LC circuit resonant on the upper band, so it isolates the outer wire there. On lower bands it acts as a loading inductor and shortens the antenna. That shortening is the reason traps cost bandwidth and some efficiency. A homebrew trap also has to be built and tuned with a dip meter or analyzer before it goes up, and the capacitor's voltage rating and tolerance matter. Moisture changes the L and C values, so sealing counts.

A fan dipole or linked dipole is easier to build and troubleshoot. A fan dipole has parallel wires from a common feedpoint, but wire spacing causes interaction, so each element needs trimming in sequence, starting with the highest band. If you only want two or three bands, I'd start there. Run each design through MMANA or EZNEC first so you know how much the interaction shifts the lengths.

  • Moderators

For choke verification, an analyzer helps. Connect it at the shack end with the antenna attached and watch whether the reading changes when you move the coax or touch it. A stable reading is a good sign, though not a guarantee. A clamp-on RF current probe is better if you have one. Compare the current on the shield on each side of the choke. If you only have an SWR meter, the same test still applies. Move the coax, add or remove a choke, and see if the numbers change.

One point on modeling the choke: NEC models a perfectly balanced dipole, so the model won't show common-mode problems unless you include the feedline as wires. If you want to see how a bad choke changes the pattern, model the coax as a vertical wire below the feedpoint. It's a rough approximation, but it shows why the choke matters.

On verticals, a quick check is the feedpoint resistance. A quarter-wave with a few elevated radials at a downward slope often reads close to 50 ohms. If you see 30 to 36 ohms, the radials are probably horizontal or the ground loss is lower than expected. That tells you something before you spend time on matching.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.