Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with satellite work: FM birds vs. linear transponders, Doppler handling, and tracking setup

ci_cover.jpg

I'd like to collect some practical thinking on moving from FM-only satellite work to linear birds, and on how people set up tracking and antennas for each. Satellite status changes often, so check AMSAT's status pages and the ARISS announcements for current frequencies, tones and what is actually switched on before you plan a pass. The principles below stay the same even when a particular satellite goes quiet.

The FM birds like SO-50 and the AO-91/AO-92 family are the usual entry point. They are single-channel crossband repeaters, so one station talks at a time and everyone shares the same uplink and downlink. Typical operation is 2 m up and 70 cm down. The exchange is short: callsign and grid square, maybe a signal report. Doppler matters here, but the receiver is wide enough that many people get by with a few manual steps in the downlink. Some satellites also need a CTCSS tone on the uplink, and SO-50 additionally needs an arming sequence, so read the current access instructions rather than relying on old notes.

The ISS is a separate case. The APRS digipeater is a simple simulplex packet setup on 145.825 MHz, and the crossband voice repeater is usually enabled only at certain times and with a tone. Both depend on what the crew and ARISS have configured, so treat any frequency you saw in an old article as a starting point and verify it.

Linear transponders are a different style of operating. RS-44 is the one most people mention because of its high orbit, which gives long passes. A linear bird retransmits a whole slice of spectrum, so SSB and CW stations share it like a small HF band. The transponder is inverting, so when you tune your uplink up, the downlink moves down. You should hear your own downlink, then adjust your transmit so the two line up with whoever you are working. Calling CQ by tuning around works, but it is easy to be loud, and a loud signal can take up more of the transponder's power than the other users do.

Doppler is the real skill test. At 435 MHz a LEO pass can shift the received frequency by roughly 10 kHz from acquisition to loss of signal, and about a third of that on 145 MHz. On FM that mostly means retuning a few times. On SSB or CW it means the station you are listening to drifts away unless you compensate. Programs like Gpredict and SatPC32 can do the correction through CAT control, shifting your uplink and downlink in step. Pick a convention, either correcting the downlink to hold your own transmitted signal steady or correcting the uplink to hold the received signal steady, and be consistent. A radio that can only be slewed in coarse steps will make this frustrating on SSB.

On tracking, the AOS and LOS times are less important than the maximum elevation. A pass peaking at 10 degrees has a short window and a lot of path loss, while a 60 degree pass is much easier. Gpredict gives you a nice pass list with a polar plot, and SatPC32 integrates Doppler control and rotator output. Keep your TLEs fresh, since stale elements are one of the most common causes of 'it's not where the software says'.

On antennas, a handheld Arrow-style dual-band Yagi with a duplexer is the classic portable setup. Satellites usually radiate circular polarization, so a linear Yagi will see fading as the satellite tumbles or changes aspect. Rotating the antenna about its boom axis can help. For a fixed station, a pair of cross-polarized Yagis on an az/el rotator gives you more consistent signals, but you then have to think about feedline loss, preamp placement and a rotator controller that can follow the software.

QO-100 is the opposite of all of this. It is geostationary, so there are no passes, no Doppler to speak of, and no rotator needed. You aim a dish once and leave it. The narrowband transponder takes an uplink at 2.4 GHz and downlinks around 10.45 GHz, so the main challenges are a stable LNB, a clean uplink chain and keeping your power low. The footprint covers parts of Africa, Europe, the Middle East and Asia, and some of South America, so check that you have a clear view to the satellite's position in the sky.

Which part should I plan first: antennas, radio, or tracking software? And for those starting on linear birds, what is the least painful way to practice Doppler before attempting a real contact?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd start with software and listening only, because it costs nothing and tells you whether your site and expectations are reasonable. Set your location in Gpredict, enter your grid square properly, and update the TLEs. Then watch a handful of passes on the polar plot and note which ones go over about 30 degrees of elevation. Once you have a handheld receiver and an Arrow, try to hear an FM bird's downlink without transmitting. Hearing a pass tells you more about your antenna aiming and your Doppler habits than a transmitted contact would.

For linear practice, RS-44 is useful because the passes are long and there is time to figure out what your radio is doing. Listen to CW beacons or SSB signals and tune the downlink until a station sounds natural. The inverting relationship takes a few passes before it becomes automatic. When you do transmit, use the lowest power that gets you a copyable signal. If you can hear your own downlink clearly at modest power, that is the right level.

  • Moderators

On the question of antennas vs. rotators: if you are on a handheld Arrow, the thing that limits you is usually how consistently you can point it, not the gain. Take the pass table from Gpredict with the AOS azimuth and max elevation, and aim slightly ahead of where the satellite will appear instead of chasing it. Also watch your feedline and duplexer losses. A small amount of extra loss on the 70 cm receive side has a bigger effect than most people expect.

For a fixed station with a rotator, there is one practical trap to watch for: the pass that goes close to overhead. Azimuth can swing very quickly near zenith, and some rotators cannot keep up. Many operators prefer a slightly lower-elevation pass for that reason, or set up the controller to avoid it. SatPC32 and Gpredict both let you tune how often they send commands, and it is worth testing with the rotator disconnected from the antennas first. For QO-100, forget all that and put the effort into mechanical stability of the dish and the LNB, because even small wind movement matters at 10 GHz.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.