Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most from 5 watts: rigs, antennas and power choices for portable QRP

ci_cover.jpg

QRP is usually defined as 5 W output on CW and 10 W PEP on SSB (the levels used in QRP-ARCI contests). QRPp is generally 1 W or less. At these levels the radio is rarely the weakest part of the station. Antenna efficiency, feedline loss, band choice, timing and operating technique usually decide the result. This thread is for comparing approaches to portable and home QRP.

Rigs. The ones people tend to compare fall into a few groups:

Full-featured portable transceivers: the Elecraft KX2 and KX3 cover CW, SSB and digital modes in a compact package. The KX2 is rated for about 10 W and the KX3 for up to 15 W on external power. Running either one at 5 W saves battery. Check the manufacturer's specs for input voltage limits and current draw before choosing a pack.

Minimalist CW rigs: the Mountain Topper line (LNR Precision) and the Penntek TR-35 are small CW-focused radios aimed at summit and park activations. They give up features such as SSB, wide coverage and a big display in exchange for low weight, low receive current and a short setup time.

Kits and experiments: Hendricks kits (the designs of Doug Hendricks, KD1JV) are popular for compact, efficient CW transceivers. The Pixie is a different kind of project. It is a very simple, very low-power CW transceiver, often built to learn how a circuit works. Its selectivity and stability are modest, so it is better as a learning build than as a main field radio.

Calling frequencies. Commonly used QRP calling areas are near 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906, 28.060 and 50.060 MHz on CW. Common SSB areas are near 3.985, 7.285, 14.285, 21.385 and 28.885 MHz. Some regions use slightly different segments, such as 7.030 versus 7.040 depending on the band plan, so check your local plan. A calling frequency is a place to meet, not a reserved channel. Many operators call CQ a little above or below it so the area stays usable.

Antennas. At 5 W every dB counts. Common choices include:

End-fed half-wave wires with a 49:1 matching transformer, which are quick to deploy and work on a fundamental band and its harmonics.

Linked or trapped dipoles, which are usually more efficient than a heavily loaded short antenna and need little or no tuner.

Vertical wires or whips with a few radials or a counterpoise, which have a low angle of radiation and are easy to put up from a pole.

Matching losses matter too. A tuner on a high-SWR feedline can waste a surprising share of your 5 W as heat in the coax. A resonant antenna with a short run of light coax is often better than a broadband compromise.

Power. Small LiFePO4 packs are popular because they hold a fairly flat voltage through most of the discharge and tolerate many cycles. A 4-cell LiFePO4 pack is nominally about 12.8 V and charges to roughly 14.4 V, so check that the top of that range is within your radio's input rating. Pack capacity, connector type, fusing and a low-voltage cutoff are worth planning. For a 5 W CW rig, transmit current is only part of the picture. Receive current often sets the total runtime, because most of the time is spent listening.

What mix of rig, antenna and power supply do you find works best for portable operating, and what would you change about it?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For efficiency I would start with the antenna and work backwards. A 5 W signal on a good resonant dipole at a reasonable height will often be heard better than 20 W into something short and lossy. If you use an end-fed half-wave, be careful with the feedline and counterpoise. The transformer, the coax length and common-mode current on the shield can all change the result. A small choke or ferrite near the radio can help keep RF off the station and out of the rig.

For the battery, count both transmit and receive current. A rig like the KX2 or a Mountain Topper-style radio listens at low current, so a small LiFePO4 pack can last a long time at 5 W CW. SSB at 10 W PEP draws more, but because speech is not continuous the average current is lower than the peak figure suggests. I would still fuse the battery lead and make sure the pack voltage stays within the radio's rated range.

  • Moderators

On the kit side, I would separate learning builds from field radios. The Pixie is a good way to understand a simple transceiver, with a crystal oscillator, a mixer and an audio amplifier doing double duty. It is not a good benchmark for portable performance because the receiver is wide and the output is small. Something in the Hendricks style, or a TR-35 build, gives you a more selective receiver, better keying and a workable duty cycle for real contacts.

Operating habits help as much as hardware. Listen before calling, use the QRP calling frequencies as a meeting point rather than camping on them, and keep exchanges short for contests such as QRP-ARCI events. Sending your call clearly at a speed the other station can copy is worth a few dB. A tuned antenna and a good CW or SSB technique will win over extra power most of the time.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.