Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting clean, effective SSB audio: mic gain, ALC, compression, EQ and bandwidth for weak-signal and DX work

ci_cover.jpg

Most SSB audio problems come from the same few things: too much mic gain, too much processing, and not enough low-frequency cleanup. A lot of "my rig sounds bad" threads end up being a gain structure problem rather than a bad microphone. Here is a baseline setup order that works on most transceivers, followed by questions for the group.

1. Start with the microphone and its position. A dynamic or headset mic held about 2 to 8 cm from your mouth, slightly off-axis, avoids most plosives and breath noise. A foam windscreen or pop filter helps. Room echo is often more audible than the mic itself, so a hard-walled shack with a desk-stand mic can sound hollow. Moving closer and lowering gain usually beats raising gain and sitting back.

2. Set mic gain with the processor off first. Speak at normal DX-calling volume, not a polite whisper. Adjust mic gain until the ALC meter moves on voice peaks but stays inside the range your radio's manual recommends. On many rigs that means little or no ALC action, or only occasional touches on the loudest syllables. ALC is not a loudness meter. When it is pinned, the radio is flattening your peaks and adding distortion, and the distortion also widens your signal.

3. Use the monitor, but know its limits. Listen on headphones so the monitor does not feed back into the mic. The monitor usually samples audio inside the radio, so it shows what your mic chain and processing sound like. It does not necessarily show distortion from an overdriven amplifier or a bad RF environment. A second receiver, an SDR, or a trusted station giving a critical report tells you more than the monitor alone.

4. Add compression conservatively. A speech processor raises average power relative to peak power, which can help when the other station is struggling in noise. It also raises background noise, sibilance and distortion. Many operators find a modest setting, often only a few dB of compression on the radio's meter, is the useful range. If you sound loud but "crunchy" or tiring to listen to, back it off. Processed audio that is easy to copy beats audio that is merely loud.

5. Shape the audio with EQ. Cutting the low end below roughly 200 to 300 Hz removes room rumble and mud, which can take up transmit power without improving intelligibility. A gentle boost in the 2 to 3 kHz region can improve consonant clarity. Make EQ changes in small steps. Heavy boosts overload the processor and make the signal sharp and fatiguing.

6. Bandwidth. A typical SSB transmit passband is about 2.4 to 2.7 kHz wide. Narrowing it concentrates power into fewer frequencies and may help in a pileup, but it also costs naturalness. Wide settings sound better for casual conversations but are less polite on crowded bands. On receive, a 2.4 kHz filter is a good general-purpose choice. Try 1.8 to 2.1 kHz when there is adjacent-channel QRM, and wider when the band is quiet and you want fidelity.

7. Sideband convention. By general amateur convention, LSB is used below 10 MHz (160, 80 and 40 m) and USB is used above (20 m through 10 m and up). 60 m is USB where channelized operation is used. Check your local rules and band plan, since conventions and allocations vary.

8. Weak stations and DX. For receiving, try fast AGC where it helps, use the passband shift or IF shift to move QRM out of the filter, and notch carriers before reaching for heavy noise reduction, which can smear speech. For transmitting, keep calls short, give your callsign clearly (phonetics when needed), and listen for the DX station's pattern before transmitting. Clean, consistent audio at a reasonable level is usually more effective than adding power, because doubling power is only 3 dB, while distortion costs intelligibility.

What mic gain, ALC and compression settings do you rely on, and how do you verify them? Do you use a separate EQ profile for DX and ragchewing?

  • Replies 2
  • Views 55
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

One check I'd add is a recording test. Record a few seconds of your transmit audio, ideally through a dummy load or at low power, and listen back with the processor off, then on. Hum, a hard "S", mouth noise and room reflections are much easier to hear on playback than live.

I'd also treat "no ALC" as a starting point rather than a rule. Radios differ: some show ALC activity even when clean, others have separate compression meters and ALC behavior that the manual explains. The thing to avoid is ALC held hard against the limit during normal speech, because that usually means distortion, splatter or both. If you run an amplifier, make sure the radio's drive is set so the amp is not being flat-topped. That kind of problem can sound fine in the monitor but awful on the air.

  • Administrators

On the DX side, I think people over-process because they assume the DX station needs "louder." Often the real issue is that the other end hears your audio mixed with QRN and a pileup, so what you want is intelligibility. A low-cut around the 200-300 Hz region and a slightly narrower transmit bandwidth can help your voice stand out without piling on compression.

For receive, I would separate two jobs. First use the 2.4 kHz filter or something narrower to remove adjacent signals, then adjust passband shift until the voice sounds natural. Noise reduction comes last, because heavy NR can make weak speech sound watery and hide the syllables you are trying to copy. When trying to work a weak station, listen to their rhythm, call when they stop, and keep your exchange short. Sending your callsign cleanly once or twice is better than sending it several times with a long preamble.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.