Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Cheap SDR chain for HF and VHF: where dynamic range, noise and antenna choice actually limit you

ci_cover.jpg

A lot of SDR questions come down to the same symptom: the waterfall is full of signals that don't exist, or the band looks dead where it shouldn't be. Before buying a new receiver, it helps to separate three different problems: front-end overload, a poor noise figure or antenna, and local noise from the computer and power supplies.

Take a typical starter chain. An RTL-SDR (RTL2832U with an R820T2 tuner) has an 8-bit ADC and a stable bandwidth of about 2.4 MHz. Below roughly 24 MHz it needs either direct sampling mode (on the RTL-SDR Blog V3 this is the Q-branch) or an upconverter. A crystal-based upconverter with a 125 MHz LO, for example, means a 7.074 MHz signal appears at 132.074 MHz. The software needs a matching frequency offset, otherwise the dial reads wrong and CAT or panadapter sync will be off.

The next tier up changes the trade-offs. SDRplay RSP-series receivers have 12-bit converters, wider coverage and built-in filtering. Airspy offers the R2 for VHF/UHF and the HF+ line for HF with strong-signal performance as its main selling point. HackRF and LimeSDR are more experimenter platforms: wide tuning range and transmit capability, but not obviously the best choice for weak-signal receive work.

Questions for the thread:

1. What is your method for setting gain? I would say the goal is to avoid ADC clipping while the noise floor with the antenna connected still rises noticeably above the terminated floor.

2. When do you reach for an FM broadcast notch or a bandpass filter instead of lowering gain?

3. Which software suits which job? SDR# and SDRuno on Windows, GQRX on Linux/macOS, HDSDR with ExtIO drivers, CubicSDR via SoapySDR. And how do you route audio to WSJT-X, fldigi or multimon-ng without adding problems?

4. For HF reception, is a small magnetic loop or active whip a better bet than a long wire with a 9:1 unun when the house is electrically noisy?

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On gain: don't tune it by how pretty the waterfall looks. A decent test is to disconnect the antenna and put a terminator on the input, then note the noise floor in the bandwidth you actually use. Reconnect the antenna. On a quiet VHF band with a reasonable antenna, the floor should rise by a few dB. If it doesn't move, you are probably running with too little gain to benefit from the antenna and the receiver's own noise dominates. If the floor rises a lot and strange carriers appear and move when you change gain, that is the classic sign of overload or intermodulation. Real signals stay put when you change gain, while intermod products often shift or change level out of proportion.

The 8-bit ADC in an RTL-SDR gives a theoretical dynamic range of about 50 dB, and real devices get less. That is why a strong FM broadcast signal can wreck reception at 100-200 MHz even when you are not listening to FM. A broadcast-band notch filter ahead of the dongle often helps more than any software setting, because the strong signal never reaches the ADC or the tuner's mixer stage. For the 1090 MHz ADS-B band, a filtered LNA placed close to the antenna usually does more than a longer cable run to a better dongle.

Bandwidth matters too. Thermal noise is about -174 dBm/Hz plus 10 log10(bandwidth), so a 2.4 MHz capture sits roughly 64 dB above that figure before the receiver's own noise figure is added. Narrowing the FFT resolution makes weak carriers stand out on the display, but it does not improve what the front end sees. Those are separate things.

  • Moderators

For HF, I would first decide whether the problem is sensitivity or noise. Below about 20 MHz, man-made noise at most locations is far higher than the receiver's own noise, so a more sensitive radio doesn't help much. What helps is an antenna that gives good signal-to-noise ratio, and that is not always the one with the most gain. A small receive loop can null a local noise source by orientation. A long wire picks up more signal and more noise, and common-mode current on the coax can bring in noise from inside the house. A common-mode choke at the feedpoint and another at the receiver end are cheap and often worth trying before anything else.

The computer is another source. Switch-mode supplies, USB 3 ports and cheap hubs can all put hash on HF. Try a USB 2 port, a short USB cable with ferrites, or a powered hub, and compare with the antenna disconnected. If the birdies stay with the antenna removed, the source is local to the receiver chain.

For digital modes, the software chain is simple but the details matter. On Windows, a virtual audio cable carries demodulated audio from SDR#, SDRuno or HDSDR into WSJT-X or fldigi. Use USB demodulation, keep audio levels below clipping, and make sure the PC clock is accurate for FT8. Frequency error is a separate issue. A dongle with a TCXO makes ppm correction far less of a chore, and it matters more at VHF/UHF and when using an upconverter, where oscillator error is multiplied into the tuned frequency.

If you want a panadapter on a transceiver, check how you split the antenna. Never connect an SDR input directly to a transmit path. Use an IF output on radios that have one, or a properly protected splitter or relay system. Then use CAT or rigctld to keep the SDR dial following the radio.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.