Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, HOA limits, 80–10 m: EFHW vs OCFD vs doublet vs vertical vs loop, and what SWR won't tell you

ci_cover.jpg

Here is a common scenario worth working through. The lot is roughly 50 x 100 ft, the HOA bans anything that looks like an antenna, and the operator runs 100 W on SSB and FT8 and wants 40 m through 10 m, with 80 m as a bonus. Which compromise makes the most sense, and what should you measure before judging it?

These are the candidates, with the tradeoffs I'd put on the table.

End-fed half-wave (EFHW). A 49:1 or 64:1 transformer at the end of a half-wave wire (about 66 ft cut for 40 m) gives you 40/20/15/10 on harmonics with no tuner. It is easy to hang as a sloper or inverted L, and one support is enough. The catches are that the feedpoint impedance is in the thousands of ohms, so transformer losses and core heating matter. There is also no true counterpoise, so the coax shield becomes part of the antenna unless you add a choke or a counterpoise wire. A common-mode choke a short distance down the coax is cheap insurance. Harmonic bands are not perfectly resonant either, so expect some bands to need a short tuner assist or trimming.

Off-center fed dipole (OCFD / Windom style). Feeding at roughly the 1/3 point with a 4:1 current balun gives a workable match on several bands from one wire. The feedpoint can be fed with ordinary coax, which is simpler than the EFHW, but the balun has to cope with different impedances per band, and the radiation patterns get lobey on the higher bands. A choke on the coax is still a good idea.

G5RV and other doublets. A G5RV is a 102 ft flat-top with a 31 ft ladder-line section into coax. It is really a 20 m 3/2-wavelength design, and on other bands it relies on a tuner. A plain doublet (any reasonably long flat-top, balanced line, tuner) does the same job with fewer assumptions. Its strength is that ladder line has very low loss even at high SWR, so the antenna works across 80–10 m. The weakness is routing a balanced line through a small yard and into the shack without letting it run close to metal.

Inverted V. Needs just one mast, and the center can be high while the ends droop toward the ground. The resonant length is a few percent longer than the same wire flat, and feedpoint impedance drops toward 50 ohms as the included angle narrows (around 90–120° is common). Keep the ends well out of reach, since they carry high voltage.

Verticals and loops. A ground-mounted vertical needs a radial field. Many short radials beat a few long ones, and ground-mounted systems commonly use 16 or more. Elevated radials resonant at 1/4 wave work with far fewer (often 2–4 per band), but the system gets bigger and more visible. A magnetic loop is small enough to hide, but it is narrow-band and needs retuning when you move a few kHz. Its efficiency depends heavily on conductor size, the quality of the capacitor and joints, and where you place it.

The thing I'd most like to discuss is how to evaluate these. SWR tells you how well the transmitter is matched to the feedline, not how much power is radiated. A dummy load is a perfect 1:1. So what do you trust: a NanoVNA, a field strength check, WSPR or RBN comparisons, or something else?

  • Replies 2
  • Views 40
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

SWR is mostly a feedline and tuner question; efficiency is a separate question, and the two get conflated constantly. Coax loss is the bridge between them. Loss per 100 ft rises with frequency, and roughly speaking RG-58 loses a few times as much as RG-213 or LMR-400 on the same run at 14 MHz. When the SWR is high, the reflected power makes the line carry extra current, so the loss goes up, sometimes by several dB on a thin cable at 10 m. A 200 ft run of thin coax into a mismatched wire can quietly eat a large part of your power.

That is the main argument for a doublet fed with ladder line. A tuner at the shack end matches whatever impedance arrives, and the line loss stays small even when the SWR on the line is 6:1 or higher. If you want to avoid a tuner, the EFHW or OCFD trade a little simplicity for fixed-ratio transformers that are good on their design bands and mediocre elsewhere.

For any of the transformer designs, the choke matters more than people expect. If common-mode current flows on the coax shield, the coax radiates, you pick up household noise, and the SWR readings change when you move the cable. A rough test is to touch the coax or move it and see whether the SWR reading shifts. A choke of 10 or so turns of coax on a mix 31 core (or a stack of clamp-on beads) is a typical starting point, but check the manufacturer's data for the band you care about, since 80 m and 10 m behave differently.

  • Moderators

On height, a horizontal wire matters more than most people expect. A 40 m dipole at about 30–40 ft (roughly 0.25–0.3 wavelength) gives a mix of low and high angles. Much lower than 0.2 wavelength and the pattern turns toward high angles, which is great for regional contacts (NVIS) but poor for DX. Neither is wrong; it depends on what you want to work. On the higher bands, even a modest height is a decent fraction of a wavelength, so a 15 m or 10 m wire can be quite effective.

A vertical makes sense if low-angle performance is the priority and you can fit radials. The weak point is almost always ground loss, not the radiator, and the radial system is what sets the efficiency. Verticals also tend to pick up more local noise on receive, so a quiet horizontal can sometimes hear better even when it is the weaker transmitter.

For stealth, thin insulated or dark-coated wire disappears against trees or a fence line. A flagpole with a hidden wire is a common approach, and an attic dipole or loop is another, though attic installs suffer from nearby wiring and ducting, and a magnetic loop indoors loses some efficiency. Whatever you build, check your RF exposure at the antenna location, since a small yard puts the antenna close to people.

For comparison, a NanoVNA is great for finding resonance, checking feedline behavior and tuning the choke. For real-world comparison, WSPR or Reverse Beacon Network spots let you compare two antennas on the same band at the same time of day, if you can switch between them quickly. That is more informative than SWR alone, though it still depends on propagation and the stations that happen to be listening.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.