Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods that are worth doing, and the ones that cause trouble: expanded RX, MARS/CAP, TCXO, filters, power and noise

ci_cover.jpg

Modifying radios covers everything from a ferrite on a power lead to opening the case and moving jumpers. Some of it is cheap and almost risk-free. Some of it can leave you with a rig that is dirtier on transmit, legally questionable, or hard to service. This thread is to sort the useful upgrades from the ones that sound good but cause problems, so it would help if people add model-specific details and test results where they have them.

Expanded receive vs. expanded transmit. These are different things, and mixing them up causes most of the legal confusion. Opening up receive coverage (airband, public service, shortwave listening, weather) is usually a software or menu change, or sometimes a jumper. It does not change what the transmitter can legally do. Transmit expansion is a separate issue. A radio's final amplifier, low-pass filters and bandpass filtering are designed around specific bands. Transmitting well outside them can mean higher harmonics and spurious output, lower power, or stress on the finals. Also note that in the US, restoring cellular-band reception on scanners is prohibited, and other countries have their own restrictions on what receivers may cover.

MARS and CAP. Many amateur rigs can be made to transmit on MARS or CAP channels, usually through a menu option, jumper, or diode change. Being able to key up on a frequency is not authorization to use it. In the US, those channels are used under the rules and assignments of the respective programs. Typically you need to be an enrolled member with the appropriate authorization, and you must use the channels and procedures the program specifies. An amateur license alone does not cover it. If you're in another country, check your national regulator and the organization involved. Before modding, it is also worth asking the program coordinator whether your model is acceptable and whether they prefer a particular configuration. For anything that transmits off the ham bands, test the output on a dummy load with a spectrum analyzer or a good receiver and a sampling setup to see what the harmonics look like.

TCXO. Frequency error scales with the operating frequency. At 1 ppm, the offset is about 144 Hz on 2 m and about 440 Hz on 70 cm, and 1 ppm on 14 MHz is only 14 Hz. That is why a TCXO matters most for VHF/UHF narrow modes, weak-signal work, and digital modes with tight tolerances. Before buying one, check your rig's actual stability spec and measure drift against a known reference such as a frequency counter or a calibrated receiver. After installing one, you may need to recalibrate the reference oscillator. A good TCXO in a rig that was already within a few ppm is not much of an upgrade.

Filters and receive performance. Adding a narrow CW or SSB filter can help in crowded band conditions, but the filter has to match the rig's IF frequency and impedance, and it has to be installed in the right position in the IF chain. Rigs with DSP-based filtering can often get most of the benefit without hardware. Roofing filters matter most when strong nearby signals overload the front end, since a narrow filter later in the chain can't fix overload that happens earlier. For handhelds, a bandpass or notch filter at the antenna can reduce broadcast or pager interference, but it adds insertion loss, so use it only where you have an interference problem.

Audio upgrades. The easiest improvements are usually outside the radio: a better microphone, correct gain staging, a headset with suitable impedance, and an external speaker. For digital modes, accessing a discriminator or data port is often better than going through the mic and speaker, but the details vary by rig. If you tap into receive audio, document the level and impedance, because levels that are too hot overdrive the sound card input. On transmit, excessive compression or overdriven audio increases splatter and wastes bandwidth, so use the ALC and the rig's metering rather than trusting the monitor audio.

Firmware. Back up the rig's memory or settings first, confirm the exact hardware revision, use the manufacturer's recommended cable and driver, and keep the rig on stable power during the update. Third-party or community firmware can add features, but it may also change the transmit spectrum, power, or protections compared with factory firmware. Verify the output on a test setup after installing it, and keep in mind that it may complicate warranty or service.

Cooling and power. Fans help on rigs that run digital modes, long transmissions, or high duty cycles. Make sure the airflow actually passes over the heatsink rather than recirculating, and check that the fan motor or its switching supply doesn't add receiver noise. For batteries, a LiFePO4 pack is a popular choice for 12 V stations because the voltage range suits most rigs, but match the voltage to the radio's rated range. Fuse the battery positive lead close to the battery, use adequate wire gauge to limit voltage drop on transmit peaks, and use a proper battery management system for the chemistry. Don't use stacked or substitute lithium cells in a handheld without a suitable protection circuit and the right voltage.

RF and noise reduction. Often the biggest improvement is finding the noise source rather than modifying the radio. Try running the rig off a battery to see if the noise changes, which tells you whether the supply or something else in the house is the culprit. Common-mode chokes on DC leads, USB cables, and feedlines, plus switching them out one at a time, usually give more benefit than any internal change. Poor grounding and bonding, and noisy LED lighting or chargers are also frequent causes.

Safe modding practice. Disconnect the battery and power, use ESD precautions, photograph the board before changing anything, and use the minimum change needed. Prefer reversible changes such as jumpers or menu settings over desoldering where possible. Keep a record of what you changed. After any transmit-related change, check the frequency, power, and spectrum into a dummy load.

Legal use of modified rigs. Amateur equipment generally can be modified by the licensee for amateur use, but it still has to meet the technical standards for the service, including spurious emission limits. Equipment certified for other services, such as commercial land mobile radios, generally loses its certification if modified outside the approved parameters. Rules differ by country, so check your regulator's current requirements. What have people found works for verifying a modified rig's output, and are there mods you would avoid altogether?

  • Replies 2
  • Views 47
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Good breakdown. One thing I'd add to the TCXO point: measure first, because a lot of people buy a TCXO to fix a problem that is really a calibration error. If the reference oscillator is simply off by a fixed amount, adjusting it may solve the problem for free. A TCXO is for drift over temperature, warm-up, and aging. If the rig drifts a lot in the first 20 minutes and then settles, a TCXO is the likely fix. If it's a constant offset, calibrate it first.

On the legal side, I'd separate three questions: can the radio do it, am I authorized to do it, and is the signal clean when it does it. Menu or jumper access answers only the first. The second depends on your license and any program membership, and the third needs actual measurement. It's easy to modify a rig and assume it's fine because the display shows the right frequency.

  • Moderators

For noise reduction, I'd start at the power and cables before touching the radio. Run it from a battery for a few minutes and compare the noise floor. If the noise drops, look at the supply and its leads. If it stays, it's coming in on the antenna or feedline, and a common-mode choke near the radio or at the feedpoint is the next thing to test. Changing one thing at a time matters, otherwise you can't tell which fix worked.

On battery upgrades, voltage range is the big issue. A rig that is rated for 13.8 V may behave differently, or protect itself, when the supply sags under transmit. A fully charged pack can also be higher than the radio expects, depending on chemistry. Check the manufacturer's rated input range and watch the voltage under load, not just at rest. A fuse close to the battery is cheap insurance, and so is a wire gauge that's generous for the current.

For fans, the sneaky problem is the fan or its controller adding hash to the receiver. If the noise appears or changes when the fan spins up, try filtering its supply lead or powering it separately from the radio.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.