Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting the most out of 5 watts: rigs, antennas, power and where to find QRP activity

ci_cover.jpg

I'd like to collect practical notes on QRP operating in one thread. Whether you're thinking about your first 5 W contact or building a pocket station, the questions tend to be the same: which rig, which antenna, how much battery, and where do people actually call?

What counts as QRP? The usual definition, including the one QRP-ARCI uses, is 5 W output or less on CW and 10 W PEP or less on SSB. Many operators think of 5 W as the practical ceiling for everything. Going from 100 W to 5 W is a 13 dB drop, a bit over two S-units on the usual 6 dB-per-S-unit convention. That is noticeable but not fatal, and a good antenna or a better location often gains more than that. Going from 5 W to 1 W costs another 7 dB, which is where band conditions and your receiver start to matter a lot.

Commercial portable rigs. The Elecraft KX2 and KX3 are the usual reference points. Both are all-mode, multiband HF transceivers with a built-in keyer and optional internal ATU. The KX2 is smaller and lighter and tops out around 10 W. The KX3 is bigger and goes to about 15 W, and it has more front-panel controls and accessory options. Check the current specs and battery options for your version before you buy. For SOTA-style CW work, the Mountain Topper line (MTR series) is a compact, low-current CW-only rig with a small number of bands. Its appeal is weight and simplicity, not features.

Kits. The Penntek TR-35 is a compact multiband CW transceiver kit that suits someone with some soldering practice who wants a useful rig at the end. Hendricks-style small kits are typically single-band CW rigs and are a good way to learn how a superhet transceiver works. At the other end are Pixie-type transceivers. These are very simple designs, with a transistor or two and a few components, and they put out well under a watt. Their selectivity is poor and the receive audio is crude. They are excellent for learning and for a quick bench build, but they aren't a good first choice if you mainly want contacts, because crowded bands will swamp them.

Calling frequencies. These are commonly cited QRP watering holes, and you should check your local band plan before relying on them: CW around 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. SSB is usually around 3.985, 7.285, 14.285, 21.285 and 28.285 MHz. Calling CQ on or near these and listening a few kHz either side helps other QRPers find you. Many people also operate simply by tuning the band and answering stations, which works fine at 5 W.

Antennas. At low power, the antenna usually matters more than the rig. Resonant wire is hard to beat for weight and efficiency: a half-wave dipole or inverted-V on a pole or in a tree, a linked dipole for multiple bands, or an end-fed half-wave with a matching unit and a short coax run or none at all. The end-fed half-wave is convenient but depends on its counterpoise and coax feed, and its losses can show up in the matching transformer, so build it carefully and test it. Height and clear surroundings help. Keep feedline short, since loss on a long thin coax run costs you a larger fraction of your 5 W than you'd like on the higher bands.

Power. LiFePO4 packs have become popular because a 4-cell pack is nominally 12.8 V with a very flat discharge curve and good cycle life. A full charge sits around 14.4 to 14.6 V, which can be close to or above some rigs' maximum input rating, so check your radio's limits. Remember that transmit current is what sizes your battery. A rig drawing around 2 A on transmit, with CW duty cycle well under 100%, will run a small pack a long time, while SSB and digital modes draw heavier average current. Also consider fusing, polarity protection and a connector you won't mix up in the dark.

Organizations. QRP-ARCI is the long-running QRP club, and it sponsors contests and awards aimed at low-power operators. If you like contesting but don't want to run high power, QRP contest categories and QRP-specific events are a friendlier place to start.

Questions for the thread: What's your favourite lightweight antenna setup for 40 and 20 m? Has anyone had good results with a Pixie or other minimalist rig, or did you outgrow it quickly? And how are you handling battery choices for a full day out?

  • Replies 2
  • Views 44
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On antennas, I'd split the choice by how you plan to operate. If you'll be at a picnic table or in a park, a linked dipole or an inverted-V on a lightweight mast is hard to beat, because it's resonant, simple, and you can see exactly what the SWR is doing. If you're trying to climb and be set up in minutes, an end-fed half-wave on a fishing pole is quicker, but it's more sensitive to counterpoise length and how the coax is dressed. A few minutes with an antenna analyzer at home will save a lot of frustration in the field.

A small point on the 5 W figure: when you're calling CQ on a QRP frequency, patience matters more than anything. Many successful QRP contacts happen because the other station is also listening carefully, not because of any clever trick. Keep your exchange short and clean, repeat your callsign clearly, and slow your CW down if the band is noisy.

  • Moderators

On batteries, I'd keep the point about LiFePO4 voltage in mind. A 4-cell pack at full charge can sit near 14.4 V or higher, and some rigs have an upper limit not far above that. Read your rig's manual for its maximum supply voltage, and consider a small regulator or a different pack arrangement if you're near the edge. The flat discharge curve is nice, but it also means you get little warning before the pack is nearly empty, so a cheap voltmeter on the pack is worth adding.

For kits, I'd suggest a simple order for learning: start with a very simple receiver or a small single-band transceiver kit, then move to something like a multiband CW kit once you're comfortable with toroids and alignment. The Pixie is fun as a first project, but treat it as a learning exercise and don't expect it to work well on a busy band. If you want a rig to use reliably on a hilltop, a purpose-built portable rig with proper filtering is more rewarding.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.