Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building an HF shack around a 100 W rig: what matters more than the radio model?

ci_cover.jpg

Most "which rig?" threads end up comparing the IC-7300, IC-7610, FT-991A, FTDX10, TS-590SG, TS-890S, K3S, KX3 and G90 on spec sheets. I'd like to talk about the parts of the shack that decide whether any of them performs well: power, grounding and bonding, RF in the shack, filtering, and layout.

Rig class first, briefly. The IC-7300 (direct-sampling SDR, single receiver) and the IC-7610 (dual receivers, dual ADCs) sit in the same ecosystem, but the 7610 is aimed at contesting and two-receiver work. The FT-991A is a do-everything box that adds VHF/UHF and a conventional superhet-with-DSP architecture. The FTDX10 and the Kenwood TS-590SG and TS-890S are more HF-focused, with the TS-890S the more serious receiver-oriented design. The Elecraft K3S is the modular, filter-heavy option. The KX3 and Xiegu G90 are really in the portable/low-power category (roughly 10 W and 20 W), which changes the amplifier, tuner and power supply questions entirely.

Power. A 100 W rig on SSB or CW draws roughly 20 to 22 A at 13.8 V on transmit peaks, so a 25 to 30 A supply is the usual minimum and a 40 A or larger one gives headroom if you add an accessory or two. Two things matter beyond the amp rating: voltage drop under load in the DC cable (use short, heavy-gauge leads and proper fusing at the source) and noise from switching supplies, which can show up as birdies or a raised noise floor on the lower bands. Powerpole distribution with fused branches is a common way to keep things tidy and safe. If you suspect the supply, a ferrite on the DC lead or a trial with a battery is a quick test.

Grounding and bonding. These get lumped together, but they do different jobs. Safety grounding protects people from fault current and follows your local electrical code. Lightning protection aims to give a surge a controlled path and keep it outside the living space. RF grounding is the murkiest: a long wire to a ground rod usually acts as an antenna or choke at HF rather than a good RF ground. The usual practical approach is to bond all station equipment together with short, low-impedance straps, bond the station ground to the service ground and any outside rods so there are no voltage differences between them, and put coax and control lines through a single entry point with surge protection. Check your local code and, for anything involving the mains panel or a tower, ask a qualified electrician.

RF in the shack. Many "my rig is flaky" problems are common-mode current on coax or USB/CAT cables, not equipment faults. Feedline chokes at the antenna feedpoint and again at the shack entry, ferrites on USB and audio cables, and keeping coax away from power and audio wiring all help. Symptoms include distorted audio, a computer interface that drops out on transmit, or SWR that changes when you touch a cable.

Filters, tuners and amplifiers. A band-pass filter is not necessary for everyone. It becomes valuable when you have a second transmitter nearby (multi-op or SO2R), strong out-of-band interference, or a receiver front end that overloads on a neighbor's signal. A tuner can only transform what it sees. It doesn't fix a lossy antenna, and a built-in ATU typically covers a limited SWR range, so a tuner at the shack end with high-SWR coax can waste power as heat in the feedline. If you add an amplifier, check how it expects to be driven, set ALC and drive level carefully, and remember it needs a decent, low-SWR load.

Layout. Keep the radio at a comfortable operating height, keep the monitor and keyboard in a sensible place, put the power supply and amplifier where their heat and fan noise don't bother you, and keep RF and AC cabling separated with clear labels.

For people with a mixed setup, where did you start: the radio, the antenna, or the grounding and power infrastructure? And which of these areas do you think gets the least attention in a typical new-station build?

  • Replies 2
  • Views 55
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put the antenna system ahead of all of it, but your point about common-mode current is the one that gets overlooked most. A lot of new stations end up with RF on the coax shield, a USB interface resetting during transmit, and a hum or buzz on the audio. The fix is often a good choke at the feedpoint (a suitable ferrite mix for the bands in use, enough turns or enough cores to give high impedance) plus a second one where the line enters the building. It costs far less than a new rig.

On grounding, I'd add that a ground rod in the yard doesn't make an HF ground. The point of the rod is safety and surge protection, and what matters most is that everything is bonded so no piece of gear sits at a different potential from another. For anything involving the mains panel, follow local code and have a qualified electrician check it. Surge protectors at the entry plate are only as good as their connection to that bonded system.

On radios, the receiver architecture matters for crowded bands more than the headline power numbers. Direct-sampling radios like the IC-7300 and IC-7610 have excellent dynamic range with well-managed gain settings, but a good band-pass filter becomes more helpful the moment you have a nearby second transmitter or a strong local broadcaster.

  • Moderators

The power supply point deserves a bit more. People often pick a supply by the continuous current rating and forget what happens on the transmit peaks. If a 100 W rig is drawing about 20 A and the supply sags or goes into current limiting, you get distorted SSB and possible ALC chatter. A bit of margin, a proper fuse close to the supply, and short, heavy DC cabling go a long way. If you're using a switching supply, also watch for hash on 160 to 40 m. A quick check with the supply on and off, or with a battery, tells you whether it's the culprit.

For the lower-power rigs, the KX3 and G90 shift the priorities. You don't need a huge supply, and a small battery or compact switcher is fine, but antenna efficiency and the choke at the feedpoint matter even more because there are fewer watts to spare. A built-in or external tuner is useful, but it only matches the radio to the line. It doesn't make a poor antenna radiate better.

For layout, one thing I'd plan early is how the amplifier will be wired. Keep its AC and RF paths physically separated from the rig's CAT and audio cabling, and leave space to access the rear panels. It's much easier to design that in than to rework a crowded desk later.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.