Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a wire antenna from scratch: where do you spend effort first, and what do you verify before trusting the SWR?

ci_cover.jpg

This is a discussion starter for anyone building HF wire antennas, dipoles, inverted-Vs, or quarter-wave verticals from raw materials. I'd like to compare notes on which parts of the build matter most and which are habit. Here is a framework, and then some questions.

Wire and length. A half-wave dipole in free space is roughly 468/f(MHz) feet overall, which is about 66 ft for 7.1 MHz. Real installations come out a few percent different because of height, nearby objects, wire diameter, and insulation. Insulated wire usually resonates lower than bare wire of the same length, so cut long and trim. Common choices are 14 AWG hard-drawn copper, 12 AWG for longer spans, and copper-clad steel where stretch is a problem. Soft-drawn copper stretches over time and drifts your resonance and your sag. Stranded wire is easier to handle and tolerates flexing better at the feedpoint.

Insulators and supports. End insulators only need to be UV-stable, mechanically strong, and not hygroscopic. At 100 W the voltage at a dipole tip is not what stresses cheap plastic. Weather and tension are what kill it. At the center, the most common failure is mechanical: coax weight pulling on a soldered joint. A center insulator with strain relief, a drip loop, and a sealed coax end all prevent trouble later. Rope should be UV-resistant, and a pulley or counterweight at one end lets the antenna move in wind instead of breaking.

Balun or choke. A dipole fed with coax wants a current balun or choke at the feedpoint. Without one, the coax shield carries common-mode current, which distorts the pattern, brings RF into the shack, and changes the SWR reading depending on how the cable is routed. Choke options include a coil of coax, ferrite beads or toroids on the coax, or a purpose-built 1:1 current balun. What matters is choke impedance on the bands you use, not whether the choke is called a balun. A choke that works on 20 m can be nearly useless on 80 m, or can heat up on the wrong mix.

Ladder line. Open-wire or window line feeding a dipole through a tuner is an old and effective way to cover several bands with one wire. Losses stay low even when SWR on the line is high. Keep the line away from metal, bring it away from the antenna as perpendicular as practical, and use a tuner with a good balanced output or a quality 4:1 or 1:1 balun at the tuner. Some line lengths on some bands produce very high voltage or current at the tuner, so it helps to model the actual combination or try a few lengths.

Verticals and radials. A quarter-wave vertical element is about 234/f(MHz) feet. The ground system matters as much as the element. Elevated resonant radials, a few of them, behave very differently from many short radials laid on the ground. A vertical with sloping radials tends toward a feedpoint impedance nearer 50 ohms, while radials at right angles give a lower figure. Buried or ground-laid radials work through quantity, so more helps up to a point of diminishing returns. A low SWR on a vertical tells you little, because lossy ground can produce a decent match and weak signals together.

Fiberglass poles. Telescoping fiberglass poles are popular for vertical wires and inverted-Vs. Check that the pole is actually fiberglass, since carbon fiber conducts and will detune a wire taped to it. Tape or tie the wire so it is not carrying the pole's bending load. Wind loading on a lightweight pole grows quickly with height, so guy it if it will stand unattended.

Traps and tuned multiband designs. A parallel LC trap isolates the outer part of a dipole at its resonant frequency and acts as loading on lower bands. The tradeoffs are narrower bandwidth, some loss, mechanical weight, and traps that must be tuned and weatherproofed. The usual alternatives are fan dipoles, which interact with each other, and a single wire on ladder line with a tuner. None of them is automatically better.

Measuring. An antenna analyzer or NanoVNA is much more informative than a single-frequency SWR reading, because it shows where resonance really is and how wide the usable range is. Measure at the feedpoint if you can. Long, lossy coax makes SWR look better than the antenna deserves. Short test cables and calibration matter on a VNA. If readings change when you touch or move the coax, you probably have common-mode current.

Modeling. EZNEC (NEC-2 engine) and MMANA-GAL (MININEC-based) are both useful before you cut wire. Model height, ground type, wire diameter, and segmentation carefully, since modeling errors around junctions and low heights can mislead. Use models to compare options and see trends, and expect to trim the real antenna.

Questions to start the thread: when you build, do you prototype with long wire and trim, or model first? What choke have you found acceptable for multiband coax-fed dipoles? And at what point do you stop adding radials on a vertical and decide the extra work isn't worth it?

  • Replies 2
  • Views 54
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the prototype versus model question, one useful approach is to do both and let the model set expectations rather than numbers. A model tells you that a dipole at 30 ft will have a different feedpoint impedance than one at 60 ft. Only the antenna on your lot tells you where it actually resonates. Trees, gutters, and the slope of the land all move things. Cutting a bit long and trimming in small steps, say a few inches per side at a time, avoids chasing your tail, and cutting both legs equally keeps the antenna balanced. Marking the wire with tape or a permanent marker at each trim point makes it easy to retrace your steps.

For the choke, a common checkpoint is to measure with and without it, with the coax routed differently. If the analyzer reading shifts when the feedline moves, the choke isn't doing enough. Several smaller chokes spaced along the line can also work better than one big one, though what's best depends on the bands.

  • Administrators

One thing worth adding about traps and verticals: both can look fine on an analyzer and still underperform, so it's worth thinking about efficiency separately from match. On a vertical, the radial field is where most of the loss lives. A short ground-mounted vertical with few radials can show a perfectly usable SWR while turning a lot of power into heat in the soil. On a trap dipole, trap Q and the wire between traps affect both bandwidth and loss. A model that includes realistic loading or loss values will show the difference between an antenna that is merely matched and one that radiates well.

For modeling, it helps to run the same antenna in both EZNEC and MMANA and see where they disagree. If the two programs disagree wildly, it usually points to a segmentation problem or ground model issue rather than a real effect. Also try varying height and ground conductivity a bit to see how sensitive the design is. If a small change in assumed ground wrecks the result, the real antenna may be fragile too.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.