From FM birds to linear transponders: building a Doppler and tracking workflow that actually works
- Replies 2
- Views 61
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Mod_Nancy 1 post
A better way to browse. Learn more.
A full-screen app on your home screen with push notifications, badges and more.
This thread is for comparing approaches to LEO satellite operating, especially the step from FM voice satellites to linear birds. The goal is to collect practical notes on the Doppler, antenna and tracking problems that come up on real passes. Please check any frequency or status I mention against current AMSAT or operator-published information, because satellite states and operating modes change.
First, the basics. FM satellites such as SO-50 and AO-91 are single-channel repeaters. Only one station at a time can use the transponder, and the uplink and downlink are fixed apart from Doppler. Some may be unavailable or restricted at any given time, and SO-50 has historically needed a specific CTCSS tone sequence to arm it. The ISS offers two options: the APRS digipeater on 145.825 MHz simplex, and the crossband voice repeater when it is enabled. The repeater's availability depends on crew schedules and hardware status, so check before building a plan around it.
Linear transponders are a different kind of operation. RS-44 is the usual example: an inverting SSB/CW transponder with a 70 cm uplink and a 2 m downlink. Many stations share the passband at once, each on their own frequency. That makes Doppler correction much more important, because you are no longer just landing on a repeater channel. You are trying to be heard at a predictable frequency inside a crowded segment, and to hear the other stations clearly.
On Doppler, the 70 cm side moves the most. For a typical LEO pass it is on the order of several kHz either side of nominal, and the 2 m shift is about a third of that. FM receivers tolerate this reasonably well if you step the frequency a few times during the pass, but SSB does not. A common method on a linear bird is to pick a downlink frequency and let the software correct the uplink so the signal stays put in the passband. Gpredict with a rig control interface and SatPC32 with its Doppler control both do this, provided your radio's CAT interface is configured correctly and the radio can accept frequency updates without muting or lagging. Some rigs handle rapid CAT updates poorly, so test the setup on a quiet pass before you rely on it.
For portable and handheld operation, the Arrow-style dual-band handheld Yagi is very popular. It is light, covers 2 m and 70 cm, and works with an HT for FM satellites. The catch is that you are doing everything at once: aiming, listening, transmitting, and correcting Doppler by hand. For linear work, many operators prefer separate receive and transmit rigs, or a full-duplex radio, so they can hear their own downlink while transmitting. A gain Yagi on a rotator is the next step up. It gives a better link margin, but it needs azimuth and elevation control, and it requires cable loss and polarization to be managed. Circular polarization or a manual polarization tweak helps with fading as the satellite tumbles or changes aspect.
Planning passes is the other half. Pass prediction needs fresh Keplerian elements, an accurate clock and your correct location. Operators usually work from the Maidenhead grid square for contacts. A four-character locator, such as FN31, is the usual exchange on voice satellites, and some operators also use six characters. Remember that contacts can be counted from both ends of a pass. Low-elevation passes give a short window and more path loss, while high passes give the most workable time. The practical question is which passes are worth the effort, and the answer depends on your antenna and horizon.
Finally, QO-100 sits outside the LEO workflow entirely because it is geostationary. The narrowband transponder uses a 2.4 GHz uplink and a 10.489 GHz downlink. There is essentially no Doppler to correct. The challenge is the dish, feed, LNB stability and keeping your transmit power in check, so you do not overpower the transponder. It is a very different skill set from chasing LEO passes, but it makes a good comparison.
Questions for the thread: What is your preferred Doppler workflow, and how do you handle rig control lag? How do you split your time between FM and linear birds? And what antenna setup gives the best results for a beginner moving from handheld Arrow operation to SSB?
Link to comment
https://www.hamradiobase.com/forums/topic/11075-from-fm-birds-to-linear-transponders-building-a-doppler-and-tracking-workflow-that-actually-works/Share on other sites