Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bench checklist before keying a first homebrew QRP transmitter (Tuna Tin 2, BITX, uBITX and similar)

ci_cover.jpg

A lot of first-time transmitter builds fail in the same few ways, and most of them can be caught before an antenna is ever connected. Whether it is a one-transistor Tuna Tin 2 style crystal oscillator, a Pixie, a BITX20, or a uBITX kit, this order of operations keeps the smoke in the parts. Corrections and additions are welcome.

1. Power supply first, with a current limit. Check the supply output with a meter before it touches the board, and confirm polarity at the connector. If you have a bench supply, set the current limit low (for a Pixie or Tuna Tin 2, 100 to 150 mA is plenty for the first power-up). A short or a wrongly installed electrolytic then shows up as a limit light rather than a burnt trace. Keep a fuse in line when running from a battery or a high-current supply.

2. Inspect and measure before applying power. Look at the solder joints under magnification for bridges and cold joints, especially around ICs, toroid leads, and the Si5351 or Arduino modules on a uBITX-style build. Measure resistance from the supply rail to ground. It should not be near zero. Check that toroids are wound with the specified turns (count turns through the core, not around the outside) and that enamel has been fully cleaned from the wire ends, since a toroid that looks connected but is not is a classic problem.

3. Check DC conditions stage by stage. Compare bias voltages and collector or drain currents against the schematic or the kit's manual. A final amplifier that draws far more idle current than expected may be oscillating, and an RF stage that draws nothing may have a missing bias resistor.

4. Always use a dummy load for the first transmit. A 50 ohm non-inductive load is the right choice for early testing. If you have an oscilloscope, measure the RF voltage across the load and calculate power: P = Vpp² / (8 × R). Into 50 ohms, 1 W is about 20 Vpp and 5 W is about 45 Vpp. That is more trustworthy than a cheap meter at very low power, and it works for a Tuna Tin 2 at a few hundred milliwatts too.

5. Look at the waveform and listen for spurs. A clean sine on the scope is encouraging but does not prove clean output, since harmonics can hide in a slightly distorted waveform. Use a separate receiver tuned to 2× and 3× the operating frequency, with the transmitter into the dummy load, to check for harmonics. Be aware that some multiband designs, uBITX included, have drawn community attention for harmonic and spur performance on certain bands depending on board revision and filter values, so verify your own unit instead of assuming the filter does its job.

6. Put the low-pass filter in the signal path and check it. Even a 1 W transmitter can produce harmonics that are legally and practically a problem. A well-built, band-appropriate low-pass filter after the final is not optional on a simple class C or class E stage. Check regulations in your own country for spurious emission limits.

7. Only then connect an antenna, through an SWR bridge. Keep early tests short, call-sign identify as required, and listen for others on the frequency before transmitting.

For direct conversion receivers there is a separate checklist: audio gain and hum, AM broadcast breakthrough, and microphonics. But for transmitters, what are the steps people find most often skipped, and are there any checks I should add?

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The scope formula is one of the most useful things a builder can have on a card taped above the bench. It is worth adding a caution that a typical x10 probe loads the circuit and has its own ground lead inductance, so on higher bands or at higher power the reading can be a bit off. For a quick check at 40 m or 20 m a short ground spring helps a lot. Always measure across the dummy load, not inside the circuit.

One more tip: for a Pixie or Tuna Tin 2, where the output is only a fraction of a watt, a diode-detector RF probe on a multimeter can be a good rough indicator. Treat it as relative, because the diode drop makes low-level readings non-linear. It is great for tuning a pi network for maximum, less great for stating exact watts.

On the Pixie specifically, expect lots of transmit-receive interaction. Its receiver is wide open, so don't be shocked if you hear several signals at once. That is the design, not necessarily a fault.

  • Moderators

Adding to the filter step: if you are using a kit with relay-switched low-pass filters, it is worth checking each band's filter on its own with a signal generator or a nanoVNA if you have one. A nanoVNA or even a tracking generator makes it easy to see the cutoff, and to verify the toroid winding counts and capacitor values were right. A filter built with a wrong capacitor value, or a toroid with one turn too many, can sit at the wrong frequency and look perfectly fine on a power meter.

Also, for low-power work the classic SWR bridge (the Tandem match or a simple Wheatstone-style bridge) has a minimum drive level, because the detector diodes need enough RF to conduct. At 200 or 300 mW the reading can look worse or better than reality. If the bridge was built for 5 W and above, don't trust it at milliwatt levels. An antenna analyzer, or a nanoVNA connected to the antenna with the transmitter off, will give a cleaner picture of the match.

On soldering: use flux, keep the iron clean, and heat the pad and the lead together. For toroid leads, scrape or burn the enamel and tin the wire before inserting. A lot of 'dead' builds come from one bad joint on a toroid or an electrolytic polarity error, so a slow second visual pass pays off.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.