Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a multi-day field comms deployment: generator vs. LiFePO4 vs. solar, and where noise and grounding bite

ci_cover.jpg

I'd like to compare approaches to a power and antenna plan for a deployment of 24 to 72 hours, such as an EMCOMM shelter support role, a served-agency backup link, or an event with no reliable mains. The goal is a station that stays quiet on receive, doesn't need constant attention, and can be torn down in the dark if it has to be.

Start with a power budget before choosing hardware. Write down each load, its current at 12-13.8 V, and a realistic duty cycle. An HF rig at 100 W on SSB can pull around 20 A on peaks, but average draw over an hour of mostly listening is far lower. Receive current on an HF or VHF/UHF rig is often only 1 to 2 A. Add the laptop, a digital-mode interface, lighting, a charger bank for handhelds, and any router or hotspot. Multiply by hours and add margin. A made-up example: 8 A average for 12 hours is about 96 Ah, which is nearly a full 100 Ah LiFePO4 battery if you keep any reserve. That is why "one battery and a small panel" often looks fine on paper and falls short by the second night.

LiFePO4 is attractive because the voltage stays flat. A nominal 12.8 V pack sits near 13.2-13.3 V under moderate load for most of its capacity, which suits radios designed for 13.8 V. Check three things on a pack: the continuous current rating of the BMS, whether it has low-temperature charge protection (charging below freezing can permanently damage cells), and what the pack does at cutoff. Some BMS units disconnect abruptly, and that drops a radio mid-transmission. Put a fuse close to the battery, use a common Powerpole orientation across the group, and size the wire for voltage drop at peak current, not average.

For charging, an inverter generator is the fast, predictable source. Solar is the quiet one, but it only helps if the array is sized for the weather you might get. An MPPT controller with a LiFePO4 profile is usually worth it over PWM, but cheap controllers can be real HF noise sources. Test the controller with the radio before deployment, not at the site. A DC-DC charger from a vehicle is another option, but treat it as a noise source too.

Questions for the group: Do you run the generator continuously, or cycle it to charge the battery and then shut down for quiet receive windows? How much separation do you plan between the generator, the operating position, and the antenna? And what is your minimum viable antenna for a regional NVIS link, given that a 33 ft fiberglass mast and a low inverted-V or dipole can be quick to raise but need guying and clearance from power lines?

  • Replies 2
  • Views 39
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the cycle versus continuous question, I'd lean toward cycling if the deployment allows it. An inverter generator is cleaner than the old open-frame type, but "cleaner" doesn't mean RF-quiet. The inverter electronics, the engine ignition, and the output cables can all radiate. The usual fixes are distance, orientation, and chokes. Put the generator well downwind and away from the operating tent, and keep its cord away from the coax and antenna wire. Clamp ferrites on the AC output cord and on any DC cable run near the radio. A mix 31 type is common for HF.

Do a noise check before you commit to a layout. With the generator off, tune across the bands you expect to use and note the S-meter noise floor with the preamp off. Then start the generator and charger and look at the same frequencies. Do the same with the solar controller connected, then with the laptop supplies and any LED lighting. Switch loads one at a time so you can identify each source. Cheap USB chargers and LED lamps are frequent offenders, and some DC-DC converters make a rough noise on 40m and 80m.

A safety point that gets glossed over: carbon monoxide. Keep the generator outdoors, well away from tent openings, doors, and vents, and never run it under a shelter, however it is open. Think about wind direction as well as distance, because exhaust can drift toward a tent when the wind shifts.

  • Administrators

For checklists, I'd separate setup into phases so nothing important gets skipped when people are tired: site survey, safety and power, antenna, station, and then a comms check. On the survey, walk the antenna fall zone and look up for lines and branches. A mast should have a clear radius larger than its height plus margin, so it can't reach power lines if it fails. Also check ground firmness, drainage, and wind exposure for the tent. Water pooling under a shelter wrecks gear, and a tarp or pallet under power distribution helps. Weights matter more than stakes on pavement.

On grounding, it helps to say what you want it to do. A short ground rod at a field site won't protect you from a lightning strike, and it usually won't fix RF noise either. The practical goals are bonding the station equipment together so a fault doesn't leave different metal at different potentials, following the generator manufacturer's instructions for its grounding and neutral bonding, and reducing common-mode current on the feedline. A choke at the antenna feedpoint and another near the shack entry often do more for noise than a ground rod. If thunder is audible, lightning is close enough to be a threat. Disconnect the coax, take the antennas down if you can do so safely, and get people into a vehicle or a substantial building. Nothing about a field setup makes it safe to stay at the mast.

Coax choice depends on band. At HF, losses on a modest run of RG-8X or similar are small and weight is the main concern. At VHF/UHF, thin coax costs more signal than most people expect, so use a lower-loss cable for any long run or keep the antenna close to the radio. Whatever you choose, label both ends, put drip loops where cable enters the shelter, and tape or strap connections so the first rain doesn't find them. On teardown, reverse the order: power down, disconnect antennas, lower masts, then coil cables and stow them with the correct labels, so the next deployment starts with known parts.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.