Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Band plans vs. FCC rules: how do you decide where to operate, and how close to the band edge is safe?

ci_cover.jpg

I'm trying to sort out the difference between what the FCC requires and what the ARRL band plan suggests. I'd like a mental map from 160 m up through 33 cm that answers a few questions:

1. Which parts of the band plan are actual law (Part 97) and which are voluntary courtesy?
2. How should I figure out where phone, CW and digital segments sit on HF, and how close to the edge can I put my dial frequency?
3. What are the usual simplex calling frequencies on 6 m, 2 m, 70 cm and 33 cm?
4. How do license classes map onto all this, and what is the story with the 60 m channels?
5. How much does it change if you operate outside the US?

Corrections are welcome if I've got any of this wrong. I know band edges and rules get updated, so please say where to verify anything time-sensitive.

  • Replies 2
  • Views 57
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

Start with the legal/voluntary split, because it makes everything else easier. Part 97 (sections 97.301 to 97.305 and related rules) is the law. It defines which frequencies each license class can use, which emission types are allowed in which segments, and power limits. The ARRL band plan is not law. It is a consensus on how to share space between modes (weak-signal CW, SSB, digital, beacons, repeaters, etc.). Ignoring it won't earn a citation by itself, but it will get you QRM and bad feelings. Going outside your privileges is a violation.

On HF, think in layers. CW and narrow digital modes sit at the bottom of each band, with phone higher up. In the US, General and Extra phone segments are:

80 m: General 3.800-4.000, Extra 3.600-4.000
40 m: General 7.175-7.300, Extra 7.125-7.300
20 m: General 14.225-14.350, Extra 14.150-14.350
15 m: General 21.275-21.450, Extra 21.200-21.450

160 m (1.800-2.000) and 10 m (28.000-29.700) are open to General and Extra with the usual mode rules. 30 m (10.100-10.150) is CW and data only, 200 W PEP. On 17 m and 12 m, phone is allowed only in the upper part of the band, and the lower part is CW/data. Technicians get CW-only segments on 80, 40 and 15 m, plus CW/RTTY/data on 10 m from 28.000-28.300 and SSB from 28.300-28.500 with a 200 W PEP limit. Always check the current FCC chart, because I'm quoting from memory.

For band edges, remember that your signal occupies bandwidth around the dial frequency. In USB (normal on 20 m and up), the signal extends above the dial, so keep the dial about 3 kHz below the upper limit. In LSB (normal on 160/80/40 m), the signal extends below the dial, so keep the dial at least 3 kHz above the lower limit. For example, if you're a General on 75 m phone, don't park an LSB signal at 3.800.0 kHz, because part of it is outside your privileges. Allow a margin for rig calibration error too. With digital modes like FT8, the transmitted signal is the dial frequency plus the audio offset (maybe 200-3000 Hz), so check the whole range.

Common digital watering holes are the FT8 dial frequencies, such as 7.074 and 14.074 MHz. Those are usage conventions, not regulations, but they work only if everyone sticks to them.

  • Moderators

I'll cover VHF/UHF, 60 m and international, since those weren't covered above.

VHF/UHF band plans are more crowded and regional than HF because of repeater coordination. The ARRL plan gives the general layout, but your local frequency coordinator decides repeater pairs and some simplex allocations. Calling frequencies you can generally rely on:

6 m: 50.125 MHz is the SSB calling frequency, with the 50.100-50.130 region used for DX. FM simplex is up near 52.525. The 50.0-50.1 section is CW and beacons.
2 m: 146.520 is the national FM simplex calling frequency. 144.200 USB is the weak-signal SSB calling frequency, with CW and beacons in the lower portion.
70 cm: 446.000 is the national FM simplex calling frequency, and 432.100 is the weak-signal SSB/CW calling frequency.
33 cm (902-928 MHz): there's less activity. Weak-signal operation is usually found near 902.100, and FM is scattered locally, so check your area's plan. This band is shared with unlicensed devices and other users, and amateur use is secondary, so expect interference from non-amateur sources.

Technician and above have broad privileges on 6 m, 2 m, 70 cm and 33 cm. Calling frequencies are for making contact, not chatting. Make the contact, then move off to another simplex frequency so others can use the channel.

60 m is a special case. In the US it's channelized: five channels, USB only for voice, and General and Extra can use them. The dial frequencies are 5330.5, 5346.5, 5357.0, 5371.5 and 5403.5 kHz. The power limit is 100 W PEP ERP relative to a half-wave dipole, which means you have to account for antenna gain. Other modes (CW, some data) are allowed with bandwidth limits. Check the FCC rules for updates, since 60 m allocations have been changed before.

Internationally, ITU Regions matter. For example, 40 m is 7.000-7.200 MHz in Regions 1 and 3 but 7.000-7.300 in Region 2 (the Americas), so a US station on 7.250 may be outside the allocation in Europe. 80 m phone limits, 6 m availability, 70 cm width (430-440 in Region 1) and 33 cm (Region 2 only) also vary, and 60 m access varies by country. If you operate abroad, follow the local license conditions and the rules of the country you are in, not just your home privileges. Look up the national regulator's band plan before you transmit.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.