Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio chain: mic gain, ALC, processor and EQ settings that help weak stations and DX get through

ci_cover.jpg

Let's pull together a practical approach to SSB audio. Most advice amounts to "don't overdo it," but it's more useful to know what each control does and which meter tells you what.

Start with the mic and room. Mic choice matters less than distance, position and room echo. A mic a few centimetres from your mouth, slightly off-axis to reduce plosives, picks up less room reflection and gives a more consistent level. A foam windscreen or pop filter helps. A mic that is bright on paper can sound harsh and fatiguing through a 2.4 kHz passband, so a modest, speech-focused response is usually better than a "studio" sound. Many rigs expect a particular mic impedance and bias, so check the manual before plugging in a different one.

Mic gain and ALC. ALC is a protection circuit, not an audio effect. Set mic gain so that on normal speech peaks the ALC meter just flickers within the range your rig's manual recommends, with no sustained or pinned reading. Heavy ALC action means the audio is flat-topped and distorted before it reaches the final amp. The signal gets wider and harder to copy, and it can splatter. With an external amplifier, keep the exciter's drive and ALC under control too, because the amp can add its own distortion if it is overdriven.

Speech processor. Compression reduces the gap between loud and quiet parts of speech, raising average power without raising peak power. A small amount can help a signal stand out in noise. Too much brings up background noise, makes sibilance and breath sounds harsh, and increases distortion products. Watch the compression meter if your rig has one and stay in the lower part of its range. Also check how the processor interacts with mic gain, because on many radios raising the gain with the processor on pushes you further into compression. Whether to use it depends on the band and the signal you are working. For a casual ragchew on a clean band, you may not need it at all.

EQ and transmit bandwidth. Cutting low frequencies, roughly below 200–300 Hz, removes boominess and wastes less power on content that adds little intelligibility. A gentle lift in the 2–3 kHz region can improve consonant clarity. Make EQ changes in small steps, because aggressive curves are easy to make and hard to judge with your own ears. If your radio offers selectable transmit bandwidth, narrower settings concentrate power into the most intelligible part of speech and take up less spectrum. Wider settings sound more natural when conditions and band occupancy allow.

Monitor function. The monitor is useful for checking relative changes like popping, hum, or the effect of the processor, but it is not a faithful picture of your RF signal. Use headphones to avoid feedback. For a more reliable check, listen on a second receiver or web-based SDR if one is nearby, or ask a station for a specific report on your audio, not just signal strength.

Sideband selection. The convention is LSB below 10 MHz (160, 80 and 40 m) and USB above it (20 m and up). 60 m is an exception, where USB is used because of channelized operation. Use the standard sideband for the band unless you have a specific reason not to, so that others can tune you in without hunting.

Receive filtering for weak signals and DX. A 2.4 kHz filter is a good general-purpose width. When there's adjacent QRM, narrowing the filter to around 1.8–2.1 kHz or shifting the passband with IF shift or passband tuning can help, with a tradeoff in naturalness. Use noise reduction in moderation, because heavy settings can make weak speech sound watery and harder to understand. If your rig has a manual notch, use it for carriers and heterodynes. Experiment with AGC speed and RF gain as well, since a strong nearby signal can desensitize the receive chain.

Working DX. Listen first to learn how the DX station is operating, including whether they are working split. Use your callsign in standard phonetics, send it clearly at a steady pace, and give your callsign when asked instead of improvising. Cleaner audio will beat a louder, distorted signal, and a good antenna will do more for a weak path than any processor setting.

What settings have people found give the best balance between punch and clean audio on their rigs? And do you prefer to leave the processor on or off by default?

  • Replies 2
  • Views 42
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One point worth emphasizing is that ALC readings aren't comparable between radios. Some rigs show a lot of movement while still being linear, and others start distorting earlier. The manual's recommended range is the best starting point, and then it's worth confirming with an external look at the signal: a monitor scope, a second receiver, or a trusted report from a nearby station.

On the processor, I'd treat it as a tool for specific conditions rather than a permanent setting. If the path is solid and the band is quiet, there is little to gain and a lot of naturalness to lose. If you're trying to be heard under a pileup or in marginal conditions, a small amount of compression can help, provided the ALC stays under control and you aren't amplifying room noise. A noisy shack or a fan in the background becomes a lot more obvious once compression is raised.

For EQ, a low cut is usually the safest first change. It tends to make a mic sound less boomy without introducing a new problem. Boosting highs is where people tend to get into trouble, since a harsh, sizzly sound is tiring to listen to and can sound worse on a narrow receive filter.

  • Moderators

On receive, it's easy to focus so much on the transmit chain that the receiving side gets ignored. Making the filter narrower doesn't automatically mean better copy. If you cut too tight, you lose the consonant energy that makes speech understandable, so the signal may seem quieter in noise but actually becomes harder to follow. Try stepping between 2.4, 2.1 and 1.8 kHz while listening to a real signal, and adjust the passband shift to move away from the interference side instead of just narrowing the whole filter.

Also check that your RF gain, preamp and attenuator choices suit the band. On the lower bands, where atmospheric noise is often higher than receiver noise, a preamp may add little and just raise the chance of overload. On the higher bands in quiet conditions, it can be more useful. If a weak station is fading, slow AGC can make the audio more stable, while fast AGC can make it pump with noise.

For DX, the most reliable habit is probably patience: listen to how the other station is working, keep your callsign short and clear, and avoid calling continuously over the top of everyone. Often, the clean signal gets the contact, not the loudest one.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.