Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 100 W HF shack: signal chain order, power, and grounding vs. bonding

ci_cover.jpg

This is a planning thread for a typical 100 W base station. The rig could be an IC-7300 or IC-7610, an FT-991A or FTDX10, a TS-590SG or TS-890S, or a K3S. A KX3 or Xiegu G90 fits the same layout at lower power. Most shack problems come from how the pieces are connected, not from which radio sits in the middle, so it's worth agreeing on a sensible order.

A common signal chain is: transceiver, then band-pass filter (if you need one), then amplifier, then tuner, then an antenna switch with surge protection at the shack entry, then the feedline. The radio's internal tuner only protects the radio. If an amp is in line, the amp needs a reasonably low SWR at its output, so an external tuner after the amp usually makes more sense than leaning on the internal one. Tune with a carrier at low power, then switch the amp in. Also remember that a tuner hides a mismatch from the radio but doesn't remove the loss in the coax. A high-SWR feedline on the upper bands can burn off a surprising share of your power before it reaches the antenna. For very mismatched antennas, a tuner at the feedpoint is a better fix than one at the operating desk.

Band-pass filters are often bought by default, but they solve a specific problem: strong out-of-band energy from a nearby transmitter, such as a second station on another band, or harmonics from a transmitter. Direct-sampling radios have band filters ahead of the ADC, and good superhet radios have roofing filters, so a lone station on a single antenna may not gain much. Filters add insertion loss, and they have to be rated for your power level, especially if an amp sits behind them.

For the power supply, a 100 W rig draws roughly 20 A or more on SSB peaks at 13.8 V. A 25 to 30 A supply is a common choice, with short, heavy DC leads so that voltage drop under transmit stays small. Some switching supplies put noise on the HF bands, so check the receive noise floor with the supply on and off. Ferrites on the DC leads sometimes help.

Grounding is where terminology gets muddled. There are three jobs: lightning protection, electrical safety, and RF behaviour in the room. Rods and bonds at the service entrance, with antenna cables entering at one protected point, handle the first two. Check your local electrical code on bonding the station ground to the mains ground. In the US that means the NEC, and other countries have their own rules. An RF ground at the radio is a separate problem. It is usually solved with short bonding straps between chassis, plus common-mode chokes on the coax and the USB, CAT and audio cables.

Questions for discussion: Where do you put the BPF in a multi-radio shack? Do you tune the tuner into a dummy load or the antenna before bringing in the amp? And has anyone compared noise floors with different supply and ferrite setups?

  • Replies 2
  • Views 59
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On filters, it depends on how the shack is used. A single operator on one antenna on one band at a time usually doesn't need BPFs. They start to matter with a multi-op or SO2R-style setup, where one transmitter's energy can reach another receiver. In that case the filter belongs on the receive/transmit path of each radio, ahead of the antenna switch. Check the filter's power rating and its SWR tolerance too. A BPF can get unhappy with a bad mismatch, which is another argument for tuning at the antenna and not just at the desk.

Where an amp is concerned, be careful with the keying line and ALC. If the amp has band data and a keyline, make sure the radio releases the relay before RF goes out. If the drive is higher than the amp wants, back the radio down to the amp's rated input rather than hoping the ALC will sort it out.

  • Administrators

One distinction to keep clear is that a ground rod doesn't make a shack safer from lightning on its own. What matters is bonding. The rods at the antenna entry, the mains ground and the shack bus should all be tied together, so that a surge raises everything to a similar potential, not just one cable. A bus bar at the entry panel with surge protectors on the coax lines is the usual way to do it. Disconnecting antennas during storms is still the only dependable protection.

For noise and RF in the shack, think common-mode current first. If you get hum, RF feedback on audio, or a USB CAT link that drops when you transmit, put a choke on the coax at the feed point and at the radio, and ferrites on the USB and audio leads. A short bonding strap between chassis helps but won't fix a feedline that's radiating. For the noise-floor question, compare the S-meter or a noise reading on a quiet band with the supply on and then unplugged from the mains (running from a battery), so you can see what the supply is adding.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.