Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building a 40/20 wire dipole from scratch: wire, feedpoint, choke, and how far to trust the model

ci_cover.jpg

I'm putting together a checklist for a first fully homebrew HF wire antenna, and I'd like to compare notes on where the real decisions are. The example is a 40 m dipole that also works on 20 m (and maybe 15 m on its odd harmonic), hung as an inverted V from a fiberglass pole or a tree, with about 60 to 70 ft between supports.

Wire. For a permanent span, 14 AWG hard-drawn copper or copperweld is a common choice. Soft-drawn copper stretches over time, and the resonant frequency drifts down as it does. Copperweld resists stretching but is stiffer and harder to coil. Stranded insulated 14 to 12 AWG is easier to handle and kinder to tight bends at the insulators. Conductor loss at HF is negligible for any of these, so the choice is about mechanical life. Gauge affects resonance a little: fatter wire shortens the electrical length slightly and widens bandwidth. Insulation also lowers the resonant frequency, so insulated wire needs to be cut shorter than bare wire.

Length. The usual 468/f(MHz) formula gives about 66 ft overall for 7.1 MHz. Treat it only as a starting point. Height, nearby objects, the inverted-V angle, and the insulation all move the resonant point. Cutting each leg 3 to 5 percent long and trimming down is safer than cutting to the formula and then having to splice wire back on. Fold the extra wire back on itself at the end insulators and don't snip it until you're done.

Feedpoint and choke. A dipole at moderate height presents roughly 50 to 75 ohms, so direct coax feed with a 1:1 current balun or a choke at the feedpoint is the simple route. A balun that is just a few turns on a small core often does little against common-mode current. A more reliable choke is a stack of ferrite beads or a multi-turn winding on a suitable core (mix 31 and 43 are common choices), with enough impedance across the bands you use. It's worth measuring the choke on a NanoVNA or antenna analyzer if you can. Strain relief matters too: the coax weight should hang from the support rope or the center insulator, not pull on the wire connections.

Ladder line option. 450-ohm window line to a tuner is a good fit if you want to cover several bands, because feedline loss stays low even at high SWR. Keep the line a few inches from metal and gutters, avoid running it parallel to the ground along a long wall, and put a choke or a good balun where it enters the shack.

Modeling. I'd like to model this in EZNEC and cross-check it in MMANA-GAL before cutting wire. The first things I plan to check are segment count per wire, correct ground type and antenna height, and how the resonant frequency shifts as the inverted-V apex angle changes. I'd treat the model as a guide to trends rather than an exact predictor of SWR, because real trees, wires, and soil are not in it.

Questions for the group: what's your approach to trimming the antenna after it's up? And is a simple coax choke enough, or is a purpose-built ferrite choke worth the effort at this power level?

  • Replies 2
  • Views 31
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On trimming, measure at the feedpoint if you can, or at least use a known length of feedline and keep it the same each time. A NanoVNA lets you see resistance and reactance, not just the SWR dip. The lowest SWR isn't always the exact resonance, especially when the feedpoint resistance is well away from 50 ohms. If reactance crosses zero at 7.05 MHz but you want 7.15, shorten each leg by the same small amount and re-measure. For 40 m, a small number of inches per leg moves the frequency noticeably, so go in small steps.

For the choke, a coiled-coax choke is better than nothing and costs nothing, but its impedance depends on the band. It can be good on one band and poor on another because of self-resonance. A ferrite choke on the coax at the feedpoint is more predictable. If your dipole is balanced and the coax drops away at a right angle, you'll see less common-mode current, but a choke is still cheap insurance. One easy test is to move or touch the coax near the shack and watch whether the SWR or reactance reading changes. If it does, the feedline is part of the antenna.

Also check your rope and insulators. UV-resistant rope and a simple pulley or weighted line at the far end keep the wire tension steady in wind, which keeps the tuning stable.

  • Moderators

On modeling, both programs are useful, but check them against each other before trusting either. EZNEC is based on NEC, so wire junctions, segment length, and ground choices matter. A frequent error is mismatched segment lengths at a junction, or too few segments on a short wire. MMANA-GAL has its own calculation engine and a handy geometry editor. Its ground handling is simpler, so differences in feedpoint impedance between the two aren't surprising. If the two agree on the general shape of the pattern and on how resonance moves when you change height, you can trust the trend, even if the exact numbers differ.

If you add traps or loading coils later, model them as loads or as inductor/capacitor elements and keep the real component Q in mind. A 40/20 trap dipole is shorter and works on two bands without a tuner, but the traps add loss and narrow bandwidth. For a first build, a plain 40 m dipole used on 20 m through a tuner on ladder line is simpler to build and to debug, though its 20 m pattern will have more lobes.

If you move on to a vertical, the radials need more attention than the radiator does. Elevated resonant radials, usually two to four, need less wire than a buried or ground-laid field, and sloping them downward raises the feed impedance toward 50 ohms. Ground-mounted verticals without a good radial field lose a lot of power as ground loss, so budget the time for that.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.