Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting real results at 5 watts: rigs, antennas, calling frequencies and LiFePO4 power for portable QRP

ci_cover.jpg

This thread is for the practical side of QRP: what works at 5 watts CW or SSB, what is worth building, and what to carry when the station has to fit in a small pack. Share what you know about rigs, antennas and power, and correct anything below that is wrong.

First, the numbers. QRP is conventionally 5 watts output for CW and 10 watts PEP for SSB, and QRPp is usually 1 watt or less. The gap between 5 W and 100 W is about 13 dB, a bit over two S-units. A decent antenna in the clear often gains more than that over a compromised one. In practice, the antenna and the operating location decide most of what you can work, and the rig matters less.

On rig choices, the Elecraft KX2 and KX3 are the all-in-one options, covering CW, SSB and digital modes in a compact package. The KX2 is the smaller one and the KX3 has more power and bands, so check Elecraft's current specifications for exact output and band coverage. The Mountain Topper line (MTR series) and the Penntek TR-35 are CW-only rigs built for light weight and low current draw. They suit summit and park activations where every gram counts. Kit-style designs such as Hendricks kits and the Pixie are a different category. The Pixie is a very simple transceiver whose receiver is crude and wide, so it is best treated as a learning project, not a main station. Hendricks-style kits are usually built around a single band and a simple, well-understood circuit.

For calling frequencies, the commonly used QRP CW spots are around 1.810, 3.560, 7.030, 10.106, 14.060, 18.096, 21.060, 24.906 and 28.060 MHz. The commonly used SSB QRP areas are around 3.985, 7.285, 14.285, 21.385 and 28.385 MHz. These are gathering points, not exclusive channels, and band plans differ by region, so check yours. Many people call CQ near these frequencies and then move off if the spot gets crowded.

Questions for the thread: what is your go-to portable antenna for 40 and 20 meters? Do you prefer an end-fed half-wave, a linked dipole, or an inverted-V? And what are people using for power, a small LiFePO4 pack or something else?

  • Replies 2
  • Views 37
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On antennas, the three common portable choices each have trade-offs. An end-fed half-wave with a 49:1 transformer is quick to deploy and works on its fundamental and harmonics, but efficiency depends heavily on the feedline and the counterpoise. A short counterpoise wire or a few feet of coax acting as one can change the SWR and the pattern. A linked dipole with a 1:1 choke at the feedpoint is a little more work to set up but more predictable, because each band is resonant and you only change the links. A simple inverted-V on a light mast or tree is a good compromise, and a flat-top dipole at a good height will usually beat a lower, bent one.

For QRP, loss is the enemy. Use thin low-loss coax, keep the run short, and avoid a lossy tuner in the line if a resonant antenna will do. A choke at the feedpoint or the rig end reduces common-mode current, which keeps RF off the keyer paddles and the rig, and can quiet the receive noise floor.

On batteries, LiFePO4 is popular because the voltage stays fairly flat across most of the discharge curve. A 4-cell pack is nominally 12.8 V and charges to about 14.4 to 14.6 V. Check your rig's maximum input voltage before connecting a fully charged pack, because some rigs have a limit not far above that. A fuse close to the battery, polarity-protected connectors, and a proper LiFePO4 charger are worth the small cost. A small pack from a few amp-hours is plenty for a few hours of 5 W SSB or many hours of CW, since receive current in these rigs is low.

  • Administrators

Building is where QRP gets interesting. A kit teaches you how a superhet or direct-conversion receiver, a VFO or DDS, a low-pass filter and a keyed final fit together, and the same parts of a rig make troubleshooting easier later. If you have not built before, a simple single-band CW kit with a good manual is a better start than a multiband one. Basic tools help more than expensive ones: a temperature-controlled iron, a decent multimeter, and a dummy load. A 50-ohm load and an SWR or power meter let you check output and harmonics before you put it on the air. Low-pass filter design matters even at 5 W, since a clean signal is part of being a good neighbor on a crowded band.

For operating, QRP-ARCI is the best-known organization, with contests, awards and a long tradition of QRP operating. Their rules and contest definitions are on their website, so check the current versions before entering. Contest exchanges often include your power level, which can make low-power stations stand out and often draws extra attention from stations hoping to log a QRP contact.

For a first CW setup, a few habits help a lot. Send at a speed you can copy comfortably, call CQ for longer than feels natural, and listen for a full cycle before calling. Be patient on a crowded band and use the calling frequencies when the band is busy. And if you are choosing between a bigger battery and a better antenna for a portable setup, the antenna usually wins.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.