Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot and HOA-sensitive HF: EFHW, OCFD, doublet or vertical, and where the loss actually hides

ci_cover.jpg

Here is a scenario to pick apart. Take a typical suburban lot, roughly 60 x 100 ft, with one tree or a 25-30 ft mast that could pass as a flagpole. Power is 100 W, and the bands of interest are 40 and 20 m for most operating, 80 m now and then, and 15/10 m when they open. There is no tower, and anything bulky draws attention. How would you rank the realistic choices?

The candidates are an end-fed half-wave (EFHW) with a 49:1 or 64:1 transformer, an off-center fed dipole (OCFD), a G5RV, a center-fed doublet on ladder line with a tuner, an inverted V, a ground-mounted or elevated-radial vertical, and a small magnetic loop. It is easy to argue about which one has the lowest SWR. That is mostly the wrong measurement, since SWR only tells you how well the load matches the line, not how much power is radiated. A dummy load has a perfect SWR and zero gain.

The places where power gets lost or where patterns go wrong are more useful to compare:

1. Matching network loss. This covers transformer core heating in EFHW and OCFD units, trap loss, and tuner loss into a high-impedance load.

2. Feedline loss at a high SWR. Coax loss is small when matched, but it rises when the SWR is high, and thin coax on the upper bands is the usual culprit.

3. Common-mode current. The coax shield becomes part of the antenna. This distorts the pattern and brings RF into the shack, and it is the usual cause of readings that change when you touch the cable.

4. Ground loss. For verticals, this is often the biggest factor.

5. Height. Roughly, a horizontal wire at 0.5 wavelength gives useful low-angle radiation, while one below about 0.2 wavelength behaves more like a high-angle (NVIS-style) antenna. At 30 ft, that is about 0.21 wavelength on 40 m, which is fine for regional work and mediocre for DX, but about 0.44 wavelength on 20 m, which is much better.

Which of these matter most for a lot like this, and which antenna would you pick if you could only put up one?

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For a lot that small, I would take the doublet fed with ladder line (or window line) and a tuner at the operating position. It is the least glamorous choice, but it avoids most of the loss mechanisms in your list. Balanced line has very low loss even at a high SWR. That is why a non-resonant doublet works on every band if you have a tuner that can handle the impedance swings. The tuner takes the loss on the really nasty bands instead of a long run of coax.

A G5RV is basically a short doublet with a specific feed. The classic version has a 102 ft top and a matching section of roughly 34 ft of ladder line, then coax down to the shack. It is designed around 20 m, where it behaves nicely. On other bands it needs a tuner, and the coax carries a mismatched signal. A 1:1 choke where the ladder line meets the coax is worth considering, because otherwise the coax shield can pick up common-mode current.

An EFHW is attractive because it is a single wire with one feedpoint and one short run of coax. A 66 ft wire for 40 m is resonant around 7.1 MHz, and the feedpoint is in the few-thousand-ohm range, hence the 49:1 or 64:1 transformer. It is multiband when the harmonics line up, which on a 40 m fundamental means 20, 15 and 10 m. The weak points are the transformer losses, a counterpoise that is really the coax shield, and the high-voltage end of the wire. A common-mode choke on the coax near the transformer is almost always a good idea. The end of the wire also needs to be out of reach, since it carries substantial RF voltage.

An inverted V solves a practical problem. You only need one support at the apex, and the feedpoint impedance drops closer to 50 ohms when the included angle is around 90-120 degrees. The resonant length also shortens slightly compared with a flat dipole. The ends hang low, so keep them where people will not touch them.

  • Moderators

On the vertical question, the thing to keep in mind is that its performance is set mostly by the ground system and the ground you are over. A quarter-wave vertical over a good ground gives a low radiation angle, which is nice for DX. Over poor soil with few radials, a lot of your power heats the earth near the base. Ground-mounted radials need a lot of wire. Dozens of radials are common advice for good efficiency. A raised system with a few resonant radials can do well, and drooping them at about 45 degrees brings the feedpoint nearer to 50 ohms. It is also physically larger than a lot of wire antennas that will fit on a small lot, so the practical answer is often a compromise such as a loaded or shortened vertical. Those trade bandwidth and efficiency for size, much like traps do on a trap dipole.

A small magnetic loop is a different kind of compromise. It is narrowband and needs retuning when you move even a few kHz, and its efficiency depends heavily on the conductor diameter and the quality of every joint and the capacitor. Voltage across the capacitor can be very high at power, so rating matters. The upside is that it can be small and placed outdoors, and its response to local electrical noise is often quieter than a wire for receive. It tends to work best when the loop is not too close to the ground, and ideally with the loop's bottom at least a good fraction of its diameter above it. For 40 m and 80 m the physical size needed for good efficiency gets large, so most small loops are better on the higher bands.

For stealth, wire is hard to beat. Thin dark or green insulated wire disappears against trees, and fine copper-clad steel is strong for the weight. Legal status varies. In the US, the FCC's PRB-1 policy covers state and local regulations, but private deed restrictions are a different situation, so read your own covenants rather than assume. Also run an RF exposure estimate if your antenna is close to neighbours, since small lots put the radiator near people.

If you are unsure which compromise is better, test them. Put each antenna up for a similar period, and compare using WSPR or the Reverse Beacon Network instead of a few random contacts. Both give you signal reports from many stations. One antenna will rarely win on every band and at every time of day, so decide which bands and distances you care about most.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.