ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Getting started in EME: what 2 m, 70 cm, 23 cm and 10 GHz each demand from your station
Starting a thread to collect the practical side of moonbounce in one place, mainly for people deciding which band to build for first. The Moon is a poor reflector at a long distance, so EME is mostly about link budget, tracking accuracy and scheduling. The mode (JT65, Q65) matters, but it only helps once the hardware is good enough.
Rough round-trip path loss is about 252 dB on 144 MHz, about 262 dB on 432 MHz, about 271 dB on 1296 MHz and around 290 dB on 10 GHz. The Moon's distance changes between perigee and apogee, which moves the loss by about 2 dB over the month. That is why many people plan skeds near perigee.
The loss rises with frequency, but the antenna gain you get from a given physical size rises too. That is why the bands split into different kinds of station:
2 m is the traditional entry band. Arrays of long-boom Yagis are common, along with a legal-limit amplifier where licensing allows and a very low noise figure preamp at the antenna. Sky noise is a large part of the system noise here, so trimming feedline loss and mismatch matters more than a fancy receiver. Beamwidths are wide enough that tracking is forgiving, but polarization is not (more on that below).
70 cm needs more gain than 2 m for the same result, but the arrays stay compact and sky noise is lower. A bigger Yagi array or a dish with a good feed is typical.
23 cm is where dishes take over. A 3 m dish at around 55% efficiency has roughly 30 dBi of gain, and a 5 m dish about 34 dBi. The beamwidth of a 3 m dish at 1296 MHz is around 5 degrees, so tracking is still easy.
10 GHz and up are dish territory. A 1.8 m dish is around 43 dBi at 55% efficiency, but its beamwidth is only about 1.2 degrees. The Moon is about half a degree across, so pointing errors of even a few tenths of a degree cost real signal. Frequency stability also matters, because round-trip Doppler on your own echo can reach several hundred Hz on 2 m, a few kHz on 23 cm and tens of kHz on 10 GHz.
Questions for the thread. What is the realistic minimum array for 2 m with JT65 or Q65? How do you decide between a Yagi array and a dish for 70 cm? And which tools do people use for sked planning and tracking? If you quote numbers, please say whether they come from measurement or from calculation.
Starting a thread to collect the practical side of moonbounce in one place, mainly for people deciding which band to build for first. The Moon is a poor reflector at a long distance, so EME is mostly about link budget, tracking accuracy and scheduling. The mode (JT65, Q65) matters, but it only helps once the hardware is good enough.
Rough round-trip path loss is about 252 dB on 144 MHz, about 262 dB on 432 MHz, about 271 dB on 1296 MHz and around 290 dB on 10 GHz. The Moon's distance changes between perigee and apogee, which moves the loss by about 2 dB over the month. That is why many people plan skeds near perigee.
The loss rises with frequency, but the antenna gain you get from a given physical size rises too. That is why the bands split into different kinds of station:
2 m is the traditional entry band. Arrays of long-boom Yagis are common, along with a legal-limit amplifier where licensing allows and a very low noise figure preamp at the antenna. Sky noise is a large part of the system noise here, so trimming feedline loss and mismatch matters more than a fancy receiver. Beamwidths are wide enough that tracking is forgiving, but polarization is not (more on that below).
70 cm needs more gain than 2 m for the same result, but the arrays stay compact and sky noise is lower. A bigger Yagi array or a dish with a good feed is typical.
23 cm is where dishes take over. A 3 m dish at around 55% efficiency has roughly 30 dBi of gain, and a 5 m dish about 34 dBi. The beamwidth of a 3 m dish at 1296 MHz is around 5 degrees, so tracking is still easy.
10 GHz and up are dish territory. A 1.8 m dish is around 43 dBi at 55% efficiency, but its beamwidth is only about 1.2 degrees. The Moon is about half a degree across, so pointing errors of even a few tenths of a degree cost real signal. Frequency stability also matters, because round-trip Doppler on your own echo can reach several hundred Hz on 2 m, a few kHz on 23 cm and tens of kHz on 10 GHz.
Questions for the thread. What is the realistic minimum array for 2 m with JT65 or Q65? How do you decide between a Yagi array and a dish for 70 cm? And which tools do people use for sked planning and tracking? If you quote numbers, please say whether they come from measurement or from calculation.
Link to comment
https://www.hamradiobase.com/forums/topic/11150-getting-started-in-eme-what-2-m-70-cm-23-cm-and-10-ghz-each-demand-from-your-station/Share on other sites