Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Cheap SDR vs. dynamic range: how to tell overload from a weak signal (RTL-SDR, HackRF, SDRplay, Airspy)

ci_cover.jpg

A lot of SDR troubleshooting comes down to one question: is the signal too weak, or is the front end being overloaded? The two look different on screen, and the fixes are opposite. Here is a framework to start from, with corrections welcome.

Dynamic range is the span between the noise floor and the strongest signal the receiver can handle before it makes its own spurs. The ADC bit depth sets the ceiling, so an 8-bit device (RTL-SDR, HackRF) has much less headroom than a 12-bit or 14-bit one (SDRplay RSP, Airspy, LimeSDR). The ADC is only part of it, though. The tuner, the LNA, the gain distribution and any front-end filtering all matter. A well-filtered 12-bit receiver can beat a wideband 14-bit one in a crowded band, because the filtering keeps the strong stuff out of the ADC in the first place.

Symptoms of overload include phantom signals that move when you change gain, birdies that appear at the same time as a strong broadcast station, a raised noise floor across the whole waterfall when you add an antenna, and signals that get worse when you turn the gain up. A quick test: reduce the gain by 10 dB. A real signal should drop by roughly 10 dB (or a bit less, if you are noise-limited). A spur produced by intermodulation will drop faster, and a signal that disappears entirely was probably not real.

Gain staging in practice: don't leave it on full AGC while you're diagnosing. In SDR#, GQRX, SDRuno and HDSDR you can usually set tuner/LNA gain manually. Start low and raise it until the noise floor on the spectrum display lifts a few dB when you connect the antenna. That tells you the receiver is limited by external noise, not its own. Past that point more gain mostly buys you overload risk.

Broadcast FM and AM are the usual culprits. An RTL-SDR on a wideband antenna near an FM transmitter can show images of it across much of the band. An FM notch filter (or a bandpass filter for the band you actually want) is often a better investment than a new receiver. Some SDRplay models include switchable notches and preselection. Airspy HF+ style receivers lean on a strong HF front end. Check the manufacturer's current specs for what your exact model does, since models and firmware differ.

HF with an RTL-SDR: there are two main routes. Direct sampling mode (available on some dongles, such as the RTL-SDR Blog V3, using a particular input) works but has limited sensitivity and little filtering. An upconverter shifts HF to a higher frequency the tuner can reach. Typical designs use a local oscillator around 100-125 MHz, so a 7 MHz signal appears at the LO plus 7 MHz. You need to set a frequency offset in the software, otherwise the display will be wrong. Upconverters have their own images and LO leakage, so a good low-pass filter before the mixer is worth having.

Noise is often local. Switching power supplies, LED lighting, USB 3 hubs, laptop chargers and the PC itself can swamp a sensitive receiver. Common-mode current on the coax shield is a frequent route into the receiver. Try a ferrite choke or a common-mode choke near the radio, run the dongle on a USB extension, and move it away from the computer. Also compare against a battery-powered laptop if you can. If the noise vanishes, you have found your source.

Antennas: a good antenna with an ordinary dongle usually beats a poor antenna with an expensive one. For VHF/UHF, a simple dipole or a discone with decent coax is a sensible start. For HF, a longwire with a 9:1 unun, a magnetic loop, or an active small loop can all work, but active antennas have their own overload limits and need clean power. A bias tee LNA near the antenna improves noise figure when your feedline is long or lossy. It does nothing for you in a strong-signal environment, and can make it worse.

Digital modes: the usual path is the SDR application demodulating to audio, then passing that to a decoder through a virtual audio cable or loopback device. WSJT-X with FT8 needs SSB demodulation at about 2.4 kHz bandwidth and accurate system time. Pager and data decoders such as multimon-ng, ADS-B decoders, rtl_433 and satellite decoders can often read IQ or audio directly. Frequency stability matters for narrow modes, and cheap dongles drift as they warm up. A TCXO model helps, and so does applying a PPM correction.

Panadapters and bandscopes: with a transceiver that has an IF output, an SDR can display the band while the rig does the receiving and transmitting. This depends on the radio. Some provide a usable IF tap, and CAT or CI-V control keeps the SDR display tuned in step with the rig. Be careful with transmit protection: do not connect a transmitter output to an SDR input, and use whatever isolation the radio's design provides.

Questions for the thread: which band are you trying to improve, what is the antenna, and how does the noise floor change when you disconnect it? Those three answers narrow things down faster than a hardware comparison.

  • Replies 2
  • Views 78
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

The "drop the gain by 10 dB" test is a good one, and I would add a second check: swap the antenna for a 50 ohm terminator. If the spurs are still there, they are internal (clock harmonics, USB noise, the dongle's own spurs). If they go away, they are coming in from outside, and then you can work out whether they are real signals or intermod from something strong.

On HackRF specifically, it has separate RF (amp), IF and baseband gain stages, so there are more ways to set it up badly. The usual advice is to leave the front-end amp off unless you really need it, and to adjust the other gain stages until the spectrum looks clean. It is a very flexible 8-bit device, and also an easy one to overload.

For upconverters, one thing people forget is the sideband and offset. If your display looks mirrored or the frequency is clearly off by the LO value, look for a setting to shift the tuning, or a spectrum inversion option in the software. Different programs handle this differently (SDR# has a shift setting, and HDSDR lets you set an LO offset), so check how yours does it.

  • Administrators

Worth separating two different goals, because the right kit differs. If you want to listen across a wide span and see what is out there, a wideband receiver with a big waterfall is fine, and the 8-bit limits only bite when something strong is close. If you want to work weak signals next to strong ones on HF, then preselection and a good front end matter more than the sample rate or the number of bits.

On software: SDR# and HDSDR are Windows-oriented, GQRX is mainly Linux and macOS, CubicSDR is cross-platform, and SDRuno is built for SDRplay hardware only. Which one is best is mostly down to which hardware you have and which plugins or decoders you need. HDSDR is popular for HF with ExtIO support and CAT control. GQRX is a nice quick tool for VHF/UHF on Linux, and it plays well with command-line decoders. It is also easy to try more than one on the same hardware, which tells you quickly whether a problem is in the radio or the software.

On noise: it is worth keeping a note of the noise floor with the antenna connected and disconnected, at a few frequencies. A before-and-after record makes it easy to see whether a ferrite, a different power supply or a new antenna position really helped, rather than relying on how it seems by ear.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.