Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Rig dead, no TX or no RX, or stuck in protection: what is your order of checks before you touch alignment?

ci_cover.jpg

This thread is for comparing troubleshooting order on HF and VHF rigs. Most of the wasted time I see described in repair discussions comes from jumping to the exciting suspects (the finals, the alignment slugs, the DSP) before ruling out the boring ones: power, connectors, switching and protection circuits. Here is a baseline sequence, and I would like to hear where people would change it.

Start with power, and measure it where it matters. A supply that reads 13.8 V open-circuit can sag badly under transmit load through a corroded plug, a tired fuse holder or a thin cable. Check at the rig's DC input with the rig drawing current, then check the regulated rails on the board (commonly 5 V, 8 V and 9 V, but use the service manual for your model). If the rig is completely dead, check the fuses, the reverse-polarity protection and the power switch or soft-latch circuit. A bench supply with an adjustable current limit helps a lot here, because a short shows up as the limit light rather than a new fuse or burnt track.

If it powers up but there is no receive, split the problem in half. Is there any noise at all from the speaker with the squelch open and the volume up? No audio noise points toward the AF stages, the speaker, the muting line or the audio amplifier supply. Normal noise but no signals points toward the front end, the band filters or relays, the mixer, the IF, or a local oscillator that is not running or not locked. On synthesised rigs, the PLL lock indication and the VCO control voltage are worth checking early. A VCO control voltage pinned at one rail usually means the loop is not locking, and nothing downstream will work until it does. The reference oscillator is the next thing to confirm, with a counter or a scope.

If receive is fine but transmit is dead, check what the rig believes it is doing. Does the TX/RX relay click? Does the PTT line actually change state at the board? Is there drive at the exciter output? Is the driver stage getting its supply? Many rigs mute or fold back the transmitter if the protection circuits see something wrong, so a transmit failure is not always a failed PA. Into a dummy load, watch what the power does as you key up. Output that is low but stable suggests a bias, drive or gain problem. Output that rises and then collapses suggests foldback or protection.

SWR protection faults deserve their own paragraph, because they are often misdiagnosed. If the rig reports high SWR or reduces power on a known-good dummy load, the antenna is not the problem. Suspect the forward/reflected detector, which is usually a small directional coupler with Schottky or germanium-type diodes. Other suspects are a dirty low-pass filter relay contact, a cracked solder joint on the RF connector, or a drifted threshold in the protection circuit. Compare the rig's reading with an external wattmeter that you trust. If the two disagree on a dummy load, the problem is inside the rig.

When the finals are blown, the part is rarely the whole story. Common contributors include high SWR, overdrive, a wrong or drifted bias setting, a supply voltage that is too high, parasitic oscillation, or a failed protection circuit that should have cut power. Before fitting a new transistor, check the driver stage, the bias network, the emitter or source resistors, the gate resistors and any protection diodes. Confirm that the replacement is the correct type and that it is mounted with proper thermal compound and torque. Set the idle current per the manual before applying full drive. Bring it up on a current-limited supply into a dummy load, ideally at reduced voltage first, and watch the current as you key. If it blows a second time, stop and look for what killed the first one.

Noise problems are easier if you split them by source. Remove the antenna and fit a dummy load, then see whether the noise stays. If it does, the noise is generated inside the rig or arrives through the DC lead. Try running from a battery or a known linear supply. If the noise disappears, the supply (often a switching one) is injecting hash, or the rig's own smoothing capacitors have aged. If the noise only appears with the antenna connected, you are looking at the station, not the radio.

On capacitor replacement, electrolytics are the usual suspects in older gear: dried out, high ESR, or leaking. Replace like for like in value, with at least the original voltage rating and suitable temperature rating, observing polarity. In switching supplies and DC-DC sections, low-ESR types matter. Where old surface-mount electrolytics have leaked, clean the residue thoroughly and inspect the tracks, because the electrolyte can corrode copper and the damage may be under the part. An in-circuit ESR meter is more useful than a capacitance meter for finding weak ones. I would not replace RF ceramics or trimmers speculatively. Do it when a measurement points to them.

Cleaning contacts is worthwhile for scratchy pots and switches, intermittent band switching and flaky relays, but use the right product. Use a contact cleaner rated as safe for the plastics involved, use it sparingly, and avoid soaking it into places where it can reach other components or lubricants. Do not file relay contacts. Re-seating connectors and socketed ICs is cheap and sometimes fixes the whole fault.

Alignment should come last, not first. Many faults get blamed on a misalignment that was never the problem, and a detuned rig can be harder to repair than a dead one. If you do need to align, follow the order in the service manual, note the starting positions of all adjustments, and use non-metallic alignment tools. You will typically want a signal generator, a frequency counter, an RF power meter or wattmeter and a dummy load, and a multimeter. A scope is needed for some steps.

For test equipment, a decent multimeter and a dummy load will take you through a large share of faults. A scope adds the ability to see oscillation, ripple on supply rails, missing clocks and distorted audio. Keep the probe ground lead short when you look at RF or fast edges, and remember that the scope's bandwidth and probe loading limit what you can trust at HF and above. An RF probe for the multimeter is a handy way to see whether signal is present and roughly how it changes from stage to stage. Always have the service manual, because the voltage tables, block diagrams and alignment procedures save more time than any instrument. For valve gear, or anything with a high-voltage supply, discharge the capacitors and be careful, since mains and HV can kill.

What would you change in this order? Do you check the PLL before the audio chain, or the other way round? And what is the one instrument you would not want to do without on the bench?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would keep that order, with one addition: look before you measure. A quick visual pass with a magnifier will often show a burnt resistor, a leaking electrolytic, a cracked joint near a heavy connector or a loose ribbon cable. Also look at anything that has been modified, because an earlier fix may be the real cause of the current fault. Photograph the board before you remove anything.

On the SWR point, an easy trap is to test the rig on an antenna and then draw conclusions. A dummy load takes the antenna, the coax and the tuner out of the picture. If the fault follows the rig onto the dummy load, the problem is in the radio. If it vanishes, stop opening the case.

On the finals, I would add the cautionary note that a quick replacement without checking bias is how people kill a second set. Measure the idle current at low supply voltage first, and do not trust that it is right just because the transistor is new.

  • Administrators

For me the PLL check comes early whenever a synthesised rig is silent on both receive and transmit. If the first local oscillator is not locked, nothing else will behave, and you can waste an hour in the IF while the actual fault is a VCO or reference problem. A counter or scope on the reference oscillator, plus a look at the VCO control voltage, settles it quickly.

If I had to choose a single instrument, it would be the bench supply with a current limit, followed by the dummy load and wattmeter. A supply that shows you the current as the rig powers up tells you a lot before you pick up any other tool. A big jump to the limit points to a short. A tiny draw means the rig is not powering up properly. A draw that creeps up points toward a failing part getting hot.

A scope is great, but it is easy to misread. A long ground clip on a 10x probe will make a clean oscillator look messy. Keep the ground short, know whether you are AC or DC coupled, and compare against the service manual waveforms where they are given.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.