Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a first homebrew QRP station: what to build first, and what test gear actually earns its bench space?

ci_cover.jpg

This is a discussion thread for anyone mapping out a first homebrew station. The aim is to compare build orders and agree on a sensible minimum of test equipment.

There are a few common routes. One is a Pixie-style transceiver or a Tuna Tin 2-class crystal-controlled transmitter. Both are cheap and small, and they teach the basics of oscillators, keying and output matching. Another is a direct conversion receiver paired with a simple CW transmitter. A third is a more complete SSB rig, such as a BITX-style design or the uBITX, which uses an Si5351-based VFO. That is more capable, but there is more to align and more that can quietly go wrong.

Some questions to kick things off:

1. Should the receiver or the transmitter come first? A receiver gives quick feedback and shows whether your soldering and layout habits are sound. A transmitter forces you to think about harmonics, load matching and what you are putting on the air.

2. Which test gear is worth having before you power up anything that transmits? A reasonable starting list is a decent DMM, a 50 ohm dummy load, an RF probe or a diode detector for your meter, and a bench supply with an adjustable current limit. After that come a frequency counter or a general-coverage receiver, an SWR bridge you have checked against known loads, and a NanoVNA for filters and antennas. An oscilloscope is useful, but it is not essential at the start.

3. For kits and builds based on published designs, how much should you trust the stock low-pass filtering? Whether the rig is a Pixie, a Tuna Tin 2 or a multiband design like the uBITX, harmonic output is worth measuring or at least checking carefully, especially on the higher bands. If you can't measure it, an extra well-built low-pass filter is cheap insurance.

4. What are the usual traps with direct conversion receivers? Examples are AM broadcast breakthrough, microphonics, hum, and no AGC, so strong signals can overload the audio stages.

Please include specifics where you can: part values, toroid types, the symptoms you saw, and what fixed them.

  • Replies 2
  • Views 52
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On order, I'd lean toward the receiver first, with one caveat: build the dummy load and a basic RF probe before either one. They take an evening, and they make every later step easier to judge. A receiver can also show you problems early. If you get hum, motorboating or strange squeals, that points to supply decoupling, grounding or layout. A transmitter will carry the same flaws onto the air.

For direct conversion, the usual fixes are fairly consistent. Put a bandpass filter ahead of the mixer to cut broadcast breakthrough. Use an audio low-pass or bandpass filter after the product detector so the audio stage isn't fed wideband noise. Decouple the supply well, and keep the VFO or crystal oscillator away from the mixer input to limit leakage. Remember it responds on both sides of zero beat, so you hear the opposite sideband unless you add a phasing arrangement. That is normal behavior for the design.

For the supply, a current-limited bench supply is the best tool for a first power-up. Set the limit low, watch the current, and raise it only if the numbers make sense. A series diode or a fuse on the input also protects against reversed polarity.

  • Administrators

On the transmitter side, the Tuna Tin 2 and Pixie are good to build as exercises, but treat them differently. The Tuna Tin 2 is a crystal-controlled transmitter of roughly a watt class. It is a good place to practise tuning the output network for maximum output into a dummy load and then checking that the result is clean. The Pixie packs a lot into very few parts, and its selectivity is limited. It is a good way to learn how the stages work, but a poor guide to what a well-designed receiver should sound like.

For the SWR bridge, don't just trust it because it moves. Check it against known resistive loads. A 50 ohm load should read close to 1:1. A 100 ohm resistor, or two 50 ohm resistors in parallel to give 25 ohms, should read near 2:1. Do this at low power. If the forward and reflected readings are way off, check the diode orientation, the toroid winding sense and the symmetry of the layout.

For low-pass filters, calculate the values with a filter tool, wind the toroids with the correct material and turn counts, and sweep the result with a NanoVNA. Powdered-iron cores such as the red (-2) and yellow (-6) mixes are common for this, but check the design's specified core before swapping. Also keep in mind that hand-wound inductors rarely land exactly on the calculated value, so sweeping the finished filter tells you more than the arithmetic does.

For soldering, tin the ends of enameled wire properly and look at the joints under magnification. Cold joints and leftover flux cause strange faults that waste hours.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.