Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Getting started with LEO satellites: Doppler, tracking software, antennas, and FM vs. linear birds

ci_cover.jpg

I'd like to collect the practical side of working amateur satellites in one thread: what actually matters on the first passes, and where people trip up. Some starting points, with questions at the end.

FM birds. SO-50, AO-91, AO-92 and the ISS voice repeater (when it's switched on) are the usual entry points. They are single-channel crossband FM repeaters, so only one station can use them at a time. Keep calls short: callsign and grid square, nothing more. Frequencies, access tones and even whether a satellite is currently active change over time, so check a current status page such as AMSAT's before you plan a pass. Don't trust old forum posts, including this one, for the numbers.

Doppler. The shift is roughly the carrier frequency times the radial velocity divided by c. With a LEO radial velocity near 7 km/s at its extreme, that works out to about ±3.5 kHz on 2 m and ±10 kHz on 70 cm. On FM that is more than a channel width, so you can't set a frequency and forget it. The usual routine is to correct the 70 cm side in small steps, say 5 kHz at a time. Most of the shift happens in the first and last minutes of a pass, with the zero crossing at closest approach (TCA).

Linear birds. RS-44 is the example most people mention for SSB/CW. It is an inverting linear transponder: the uplink sideband flips, so you transmit LSB and hear USB, and tuning your uplink up moves the downlink down. Many stations work it with tracking software that drives the radio's CAT interface so Doppler is corrected on both ends. Others tune by ear, adjusting only the downlink and keeping their transmit on a fixed offset. The goal is to hear your own signal at about the same pitch as the other stations. Keep your uplink power modest. Over-driving a transponder, or being heard far louder than the beacon, is rude because it desensitizes everyone else on the passband.

Tracking software. Gpredict is free and good for pass prediction, a map view, and rig and rotator control. SatPC32 is Windows-only and popular for its radio and rotator control with per-satellite frequency and mode tables. Both need fresh Keplerian elements (TLEs). Stale ones can put the AOS time and azimuth well off after a few weeks. Set your location with a six-character Maidenhead grid or exact lat/long. Even if you only exchange the four-character grid on air, accurate coordinates give better azimuth and elevation.

Antennas. A handheld dual-band Yagi such as an Arrow-style 146/437 antenna is the classic minimal setup for FM. You aim by hand, usually using your tracking program's az/el. Because the satellite antenna's polarization rotates and fades, small adjustments in roll and tilt can matter as much as pointing. For fixed stations, a pair of Yagis (often cross-Yagi for circular polarization) on an az/el rotator lets you work low-elevation passes with less fading. Watch for the "keyhole" on near-overhead passes, where the azimuth swings quickly near the zenith and a rotator may lag behind. For ISS APRS on 145.825 MHz in FM, even a modest vertical often works for digipeating during a good pass.

QO-100. This is a different world: a geostationary satellite, so no Doppler tracking and no pass planning. The narrowband transponder uses a 2.4 GHz uplink and a 10.489 GHz downlink. Dish alignment, an LNB with a stable oscillator, and a clean transmit chain matter far more than rotators and software.

Questions for the thread: what's the best order to learn this (FM first, then linear)? How do you handle cross-polarization nulls with a handheld Yagi? And how much does Doppler automation actually help on SSB compared with just tuning by ear?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd start with FM, mostly because it teaches pass geometry without needing CAT control or a full-duplex rig. Look up the pass, note AOS and LOS, the maximum elevation, and which direction the satellite approaches from. Then practice just hearing the downlink before you transmit. Plenty of people find that after a pass or two of listening, the Doppler on 70 cm makes sense. The signal is high at AOS and slides lower, and you need to follow it.

On the handheld-Yagi question, a few habits help. Point the boom at the satellite rather than toward where it is on the map. Use the elevation as well as the azimuth, because the main lobe of a 3-element Yagi is not wide. If the signal fades up and down, try rotating the antenna about its boom axis a quarter turn. Linear polarization against a spinning or tumbling satellite antenna will not always give a stable signal, so you have to tolerate some QSB. Also use a headset or earphone if you're running full duplex. Hearing your own downlink in a speaker can feed back into the handheld's microphone.

For TLEs, update them before every operating session if you can, not once a month. It takes seconds and avoids "the pass was ten degrees off" confusion.

  • Moderators

On SSB, automation helps most with the details that are tedious to do by hand. With an inverting bird like RS-44, you have to move the uplink opposite to the downlink, and also correct both for Doppler. Software that does both lets you tune the downlink dial and have your transmit frequency follow it, so you can hear a station calling CQ, answer on the right frequency and stay in the passband. If you tune by ear without automation, it is workable, but you will tend to chase your own signal around during the first few minutes of a pass, which is where the shift is largest.

One practical tip about Gpredict and SatPC32: set up the radio's mode and offset in the tracker. Many beginner problems come from uplink and downlink drifting because the radio's RIT/XIT, split or sideband was set wrong, not from the software. Listen to your own signal on a second receiver, or an SDR, before you assume anything is broken.

For a mixed station, a common step up from handheld Yagi is a small az/el rotator with two Yagis on a short boom. Make sure the controller's elevation limits and the cable strain relief are right before the first live pass. And keep power low on the uplink: with a good antenna, a few watts is often enough, and a nearly full-power signal on a linear transponder will wipe out the weaker stations.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.