Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Radio mods that are worth doing, and where modifications stop being legal: expanded RX, TCXO, filters, firmware, power and noise

ci_cover.jpg

This thread is for sorting radio modifications into three groups: ones that usually help, ones that depend on the rig, and ones that cause trouble. It's also about the legal line, which gets blurry once you open the menu or the case.

Receive-side changes are usually the lowest risk. Expanded receive, whether by menu, software, or a diode or jumper change, lets a rig tune outside the ham bands. That alone doesn't change what the transmitter does. Wideband receive often comes with poor selectivity and image rejection, though. Many handhelds and mobiles pick up strong broadcast FM, pagers, or business-band signals because the front end isn't well filtered. A bandpass or notch filter in line with the antenna, or a better IF filter in a rig that has a swappable one, often does more for real-world reception than any added coverage.

Frequency accuracy and TCXO. A temperature-compensated crystal oscillator helps most on rigs that drift as they warm up, especially for narrowband digital modes, weak-signal work, or anything where a few hundred hertz matters. The usual caveats are that the replacement part must match the original frequency and supply voltage, and the rig needs recalibrating afterward against a known reference. Without that, you've swapped a part without improving anything. Also check whether the rig's PLL and firmware tolerate the change.

Audio. Transmit audio is normally improved with the mic gain, compression, and EQ settings the radio already has. Overdriving the mic and splattering is a common cause of bad audio. On receive, an external speaker with a decent enclosure often beats an internal mod. For data and digital modes, a flat-audio or discriminator tap needs care. Some rigs expose it on a data port, others need an internal connection, and an incorrect tap can degrade performance or damage the radio.

Firmware. Before flashing, back up the memories and any calibration data the tool supports. Use the correct hardware revision file and don't interrupt power during the flash. Treat third-party firmware as a separate decision: it can add useful features, but it may change transmit behavior, power levels, or frequency limits, and a failed flash can leave the radio unusable.

Cooling and power. A fan can help a rig at high duty cycle, such as FT8, RTTY, or long digital sessions, but fan hash and the motor's wiring can become a noise source. A thermostatic or switched fan that runs from a clean supply is better than one that is always on. For batteries, remember that voltage sag under transmit load can cause low-power or distorted output. Fuse the positive lead close to the battery, use adequately sized wire, and add a low-voltage cutoff for lithium chemistries. Don't put a different lithium pack in a radio designed for another chemistry without proper protection circuitry.

Noise reduction. Before modifying the radio, find the noise source. Switching supplies, LED lights, chargers, and computer cables often cause more noise than anything in the rig. Ferrite chokes on the DC and USB leads, a better ground, and moving the antenna away from the noise source are cheap tests. A battery-powered portable receiver helps tell whether the noise is local to your equipment or comes from the neighborhood.

MARS, CAP, and legal use. Rules vary by country, so check your own regulator. In the US, amateur transmitters generally aren't type-accepted the way commercial radios are, but this doesn't mean any frequency is available. Transmitting outside the amateur allocations requires authority for the service in question. MARS and CAP operation depends on membership, authorization, and assigned frequencies. Those programs set their own rules for which equipment and programming are acceptable. Opening a radio's transmit range on a rig that has not been approved for the service you want to use it in may be a violation even if the hardware allows it. Modifying a certified GMRS, FRS, or commercial radio can also void its certification.

What mods have you found are worth doing on handhelds and HF rigs, and which ones created more problems than they fixed? Please include the model, the change, and how you verified it, such as a dummy load, spectrum analyzer, or frequency counter.

  • Replies 2
  • Views 40
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On verification, a mod isn't finished until you've measured it. After any change in the transmit path, I'd want to see the output into a dummy load on a meter, a check for harmonics and spurs if you have a spectrum analyzer or a second receiver, and a frequency check after warm-up. For a TCXO swap, use a counter or a known reference such as WWV or a calibrated signal source. Don't rely on the radio's own display.

On the legal side, the useful question is whether the radio is operating where you're authorized to transmit and in the manner the service requires. An unlocked radio is only a tool. Programming CAP or MARS channels into a radio is not the same as having authority to use them. Unauthorized use of those frequencies can have real consequences, so the safest path is to check with the program's own communications officer or published policy.

  • Moderators

I'd put power wiring and noise at the top of the list, since they affect nearly every setup. For a mobile or base rig, check the supply voltage while transmitting, not just at idle. A thin wire or a poor crimp can make a good rig sound weak. Powerpole connectors, proper fusing, and a short, thick DC run are not glamorous, but they prevent more problems than most internal mods.

On filters, I'd be a bit cautious about buying one just because it's available. First work out what is overloading the receiver. If it's FM broadcast, a broadcast-reject filter makes sense. If it's a local transmitter on a nearby band, a bandpass filter or a better antenna placement may be more useful. For fans, I'd choose a quiet one, power it from a switched or filtered source, and test for added noise on the bands you use before closing the case.

For firmware, read the release notes and the user reports for your exact hardware revision. A newer version isn't automatically better, and a fix for one feature can change something else you depend on.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.