Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

No TX and no RX on a rig: a practical order of checks before you start swapping parts

ci_cover.jpg

A rig that is dead on both transmit and receive is usually easier to diagnose than one with a single odd symptom, because the shared parts are limited: power, the control or logic section, the reference oscillator and PLL, the antenna changeover, and sometimes the audio path. Here is a suggested order of checks. Please argue with it or add to it.

Start with power, and measure it at the radio's DC input connector while the rig is switched on and, if possible, while transmitting. A supply that reads 13.8 V with nothing connected can sag badly under load. Corroded fuse holders, tired power connectors and thin cable all drop voltage. If the rig has a reverse-polarity diode or a series protection device, check that it is not running hot or open. On a switch-mode supply, look at the output with a scope, not only a multimeter, because a meter will average out ripple and spikes that can upset a PLL or add noise.

Next, check the internal regulated rails against the service manual's voltage table: typically a 5 V logic rail, an 8 V receive or transmit rail, and the PLL supply. A missing rail points you at a regulator or at whatever is loading it. An unexpectedly low rail with a warm component nearby often means a shorted bypass capacitor. If the display is blank or garbled, also consider the backup battery and the memory. Odd behaviour after a long time on the shelf can be a dead lithium cell or corrupted settings that need a reset.

If power and logic are fine but there is no receive, check the audio end first. Squelch settings, the volume control, the speaker jack's switching contact and the audio amplifier are quick to rule out. Then work backwards from the detector using signal tracing or injection. With a signal generator you can step through the antenna relay, front-end filters, mixer, IF filter and demodulator and see where the signal disappears. Do not forget the local oscillator. If the PLL is not locking, the receiver and transmitter can both be dead, and the unlock line or the VCO control voltage will usually show it. A scope or counter on the reference oscillator is worth the five minutes.

On the transmit side, break the chain into PTT, modulation or drive, driver, final, low-pass filter, and the SWR or power detector. Always use a dummy load. If the rig folds back power into a good dummy load, suspect the protection circuitry itself: the forward and reflected detector diodes, the sampling bridge, the ALC or foldback amplifier, or dirty low-pass filter relay contacts that create a mismatch. If it behaves on the dummy load but folds back on the antenna, the problem is outside the rig.

When finals have failed, the replacement is rarely the whole story. High SWR, over-voltage, parasitic oscillation, a failed bias network or a driver delivering too much power can all kill a transistor. Check the bias resistors, diodes and thermal-tracking parts before fitting a new device. Use the correct part, set the bias to the manual's minimum before power-up, and use a current-limited bench supply. Then bring the idle current up to the specified value and verify the output on a dummy load with a power meter.

For capacitors, electrolytics in power supplies and audio stages are the usual suspects, and ESR matters as much as capacitance. Replace like with like: voltage rating at least equal, 105 °C low-ESR types in supply roles, and careful cleaning where leaked electrolyte has attacked traces. Be more careful with small ceramics in oscillators, filters and matching networks. The dielectric (C0G/NP0 versus X7R, for instance) changes drift and tolerance, and a substitution can shift frequency or alignment.

Contact cleaning also has its place. Use a proper contact cleaner on switches, pots and relays, avoid soaking sealed parts, and do not over-lubricate. Scratchy controls may also be DC leaking through a coupling capacitor, which cleaner will not fix. Finally, leave alignment alone until the basics are proven. Calibrate the reference first, mark slug positions, use a non-metallic tool, and follow the manual with a generator, counter, dummy load and power meter.

What do you check first when you open the case, and which test instrument do you reach for before the multimeter?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd add one thing to the power section: do the voltage check dynamically. A meter on the supply terminals tells you very little if the radio's own lead has a poor crimp or the fuse holder is high resistance. Measure at the radio's connector while keying into a dummy load, and watch whether the reading collapses. On some rigs a brownout resets the CPU or drops the PLL out of lock, which looks like a dead radio.

For mains-powered gear that you cannot yet trust, an incandescent lamp in series with the live feed (a lamp limiter) is a cheap and useful safeguard. It limits fault current if a rectifier, filter capacitor or switching device is shorted, and a bright lamp tells you immediately that something is drawing too much. For DC rigs, a bench supply with the current limit set sensibly does the same job. Either way, you can power things up without turning one fault into three.

Also on foldback: if the dummy load gives a low SWR reading on an external meter but the radio still cuts power, the radio's detector is the suspect, not the load. Compare the radio's own indication against an independent wattmeter before touching any trimmers.

  • Moderators

Multimeter first, scope second, but the scope answers a different question. The meter says whether a DC rail is present. The scope shows whether it is clean, whether an oscillator is actually running, and whether a switching supply is producing hash that ends up in the receiver. When a rig is noisy, a good test is to run it from a clean battery or linear supply. If the noise vanishes, look at the SMPS, its output filtering and the ferrites. If it stays, disconnect the antenna and see whether the noise is internal or external.

A few cautions on scope use. A probe's ground lead is an inductor, so for RF-ish signals keep it short or use a spring tip. A 10x probe loads a circuit far less than a 1x. Never connect the scope ground to a point that is live with respect to mains earth, such as a non-isolated switching supply primary, without an isolation transformer. A meter or scope is not an RF power measurement either. For output power, use a dummy load and a wattmeter or a proper RF probe.

On capacitor swaps, I'd mention that replacing every electrolytic on a hunch can introduce new faults. It's better to test a suspect first, with an ESR meter if you have one, or by looking for bulging, crust and discolouration, and then change the ones that are actually out of spec. It keeps the original behaviour clear, which helps if the problem turns out to be somewhere else.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.