Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Before adding an amp: what order do you tackle bonding, common-mode chokes, filtering and power in an HF shack?

ci_cover.jpg

This is a discussion starter about priorities in a typical modern shack. Picture a 100 W class transceiver (IC-7300, FT-991A, FTDX10, TS-590SG and similar), a wire or vertical antenna fed with coax, an external tuner, and a plan to add a legal-limit or 500 W amplifier later. There are many ways to spend money and time here, and some fixes only work once others are in place.

This is the order I would argue for, and I'd like to hear where people disagree:

1) Safety bonding and lightning protection. This means equipment grounds, a bonded entry point for coax, and a plan for disconnecting or shunting antennas. It is not about making the receiver quieter.

2) Common-mode current control. That means a choke at the feedpoint, a choke where the coax enters the shack, and a check that the antenna system is balanced where it needs to be.

3) Power supply sizing and DC wiring. A 100 W rig draws roughly 20 A on transmit, and the DC leads and fuses matter as much as the supply.

4) Layout and cable routing, especially USB, CAT, audio and amplifier keying lines.

5) Band-pass filtering and receiver front-end protection, if you actually have a nearby-station problem.

The thing I'd most like to clear up is the idea that a ground rod is the RF fix for a shack. Rods are mainly for lightning energy and for bonding to the building's grounding electrode system. RF problems like hot microphones, distorted audio, erratic CAT or USB behavior, and a tingle on the chassis are usually common-mode current on cable shields, not a missing earth connection.

Questions for the thread: what symptoms would make you move a step up the list? When does a band-pass filter bank make sense for a single-operator station? And at what point does adding an amplifier justify reworking the grounding and cabling rather than just plugging it in?

  • Replies 2
  • Views 28
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd keep two ideas separate, because mixing them causes most of the confusion. Safety bonding means all the metal chassis, the entry panel, the mains safety ground and the building grounding electrode are tied together so there is no dangerous potential difference between them during a fault or a nearby strike. Local electrical code governs that. In the US, NEC Article 810 covers antenna systems, and the general advice is to bond any separate antenna ground rod to the main service ground rather than leave it isolated. RF behavior is a different matter. A long green wire to a rod outside has a lot of inductance at HF, so at 14 MHz and up it is not a low-impedance path to anything.

That is why the common-mode chokes in your step 2 usually matter more for operating problems. A rough approach is to wind a few to a dozen turns of the coax itself on a suitable ferrite core, often a type 31 mix for the lower HF bands, close to where the coax enters the room. A second choke at the feedpoint helps keep the outside of the shield from becoming part of the antenna. If the problem changes when you move a cable or touch the rig, you're probably chasing common-mode current. If it changes with band, suspect resonance of the feedline or a cable length near a quarter wave.

For the entry point, a single bonded panel with surge protection on the coax and a short, heavy bond to the building ground is better than scattered individual grounds. A wide copper strap or braid is also better than thin wire, because lower inductance matters more than gauge in this case. Disconnecting coax from the equipment when you're away is still the most reliable lightning protection.

  • Moderators

I'd move power and layout ahead of filtering for most single-operator stations, and add a few details on each.

Power: size the supply with headroom. A 100 W transceiver on 13.8 V typically needs around 20 A at full output, so a 25 to 30 A supply is a sensible minimum and the rig's manual gives the exact figure. The weak points are often the DC leads, connectors and fuses rather than the supply. Voltage drop on thin or long leads shows up as a rig that makes less power or distorts on peaks. Some switching supplies put noise on HF receive, so if you hear a birdie pattern that disappears when you switch to a battery or a different supply, you have found the cause.

Amp and tuner: an external tuner only changes what the rig or amp sees. It does not change what the antenna does, so a lot of power can be lost in the tuner or the feedline if SWR is high at the antenna end. With an amp, set the drive and ALC according to the amp's manual rather than driving it into compression, and double-check the keying line, since a miswired or noisy amp keying line can damage a rig.

Filtering: for one operator on one band at a time, a band-pass filter is usually a solution to a specific problem, such as a strong local station overloading the front end. Multi-transmitter stations that run two radios on different bands at once need them far more. Any filter adds some insertion loss and must be rated for your power. Many modern radios, such as those with strong preselection or good dynamic range, may not need one at all, so check whether you have a real overload problem before buying.

Layout: keep coax, DC leads and USB or audio cables from running in parallel bundles where possible. Cross them at right angles if you have to, and put ferrites on USB and CAT cables near each end. Ground loops between a PC and the rig through USB audio can cause hum, so isolate the audio path first if you hear it.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.