Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Starting EME: what each band really demands (2 m, 70 cm, 23 cm, 10 GHz), JT65 vs Q65, and how to plan a first sked

ci_cover.jpg

This thread is meant as a practical starting point for comparing the bands and for discussing where a first moonbounce station should put its effort. The figures below are rough planning numbers, not a design spec. Check them against your own antenna data and local power rules.

Start with the path. Round-trip loss to the Moon is very roughly 252 dB on 144 MHz, 261 to 262 dB on 432 MHz, 271 dB on 1296 MHz and close to 290 dB on 10 GHz. Antenna gain on each end offsets most of that. Because EME loss follows the fourth power of distance, the swing between perigee and apogee is about 2 dB, so the same station is noticeably easier at perigee. Moon declination, sky noise behind the Moon and your own horizon matter as much as raw power.

On 2 m, the usual entry point is an array of several long-boom Yagis (four is a common minimum, more is better) with power in the several-hundred-watt to legal-limit range. Sky and galactic noise are high on this band, so an extremely low noise figure buys less than it does higher up, and the Moon position relative to the galactic plane changes your noise floor a lot. Beamwidth is wide enough that tracking is forgiving, and many arrays can be elevation-steered. The cost is the big mechanical structure and the polarization problem described below.

On 70 cm, expect to use four or more long Yagis, a larger Yagi group, or a dish. Gain per square metre is higher, the structures are smaller, and Faraday rotation is much less of a nuisance. Pointing precision starts to matter, and Doppler and spread are bigger than on 2 m.

On 23 cm, dishes dominate. For scale, a 3 m dish at 1296 MHz with decent efficiency is roughly 30 dBi, with a beamwidth near 5 degrees. A 4 m or larger dish is a noticeable step up. At this point receiver noise matters. Low-loss feed lines, a mast- or feed-mounted LNA with very low noise figure, and careful T/R sequencing are required, because a few tenths of a dB lost ahead of the preamp are straight lost signal. Linear and circular polarization are both used, so check the convention with your partner. After reflection the circular sense reverses, which is why the common arrangement is to transmit one sense and receive the opposite.

On 10 GHz, a 3 m dish gives roughly 47 dBi but has a beamwidth well under a degree, which is about the size of the Moon itself. Surface accuracy, feed placement, mechanical stiffness, tracking accuracy and wind loading become the real project. Doppler shift and Doppler spread are large, so JT65C-type tone spacing (or the Q65 submode recommended for the band) is used instead of the narrower choices that suit 2 m.

On modes: JT65 has long been the standard for weak-signal EME, with JT65A common on 2 m, JT65B on 70 cm and 23 cm, and JT65C on the microwave bands. Q65 in current WSJT-X releases is the newer option, designed to work well with fading and Doppler spread, and it can give a dB or two of improvement in some conditions. Both use one-minute T/R periods and compact shorthand messages for the end of the QSO. Check the current WSJT-X documentation and the activity on your band before choosing a submode, because 60 A to 60 D are matched to spread, which grows with frequency.

Libration fading is the rocking motion of the Moon, which spreads the echo in Doppler and makes the signal flutter. It scales roughly with frequency, from a very small effect on 2 m to a major one on microwaves. It is one reason wider tone spacing is used on the higher bands, and it is why you may see an echo that is strong but not decodable.

Questions for the group. Which band is the best use of a limited budget for someone starting from nothing? How much of the plan should go into tracking and preamp quality compared with antenna size? What is the simplest way to verify the station before the first sked: Sun and Moon noise measurements, own echoes in the WSJT-X Echo tool, or listening for a known big station?

  • Replies 2
  • Views 36
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On band choice, the honest answer is that it depends on what you can build and host. If you have room for a stack of long Yagis and a tall mast, 2 m is the most accessible, but you will have to handle polarization and noise. If you have a decent dish and a good feed, 23 cm tends to make better use of a smaller footprint, and polarization trouble largely goes away. 70 cm is a decent middle path, but it is usually the least crowded on the calendar.

Faraday rotation is the thing most people underestimate on 2 m. The ionosphere rotates the plane of polarization, and this varies with time, ionospheric conditions and path geometry. On top of that, there is a purely geometric offset between your horizontal and your partner's, depending on where each of you is relative to the Moon. Fixed horizontal polarization can give you deep nulls for long stretches. The practical fixes are a polarization-rotatable array, which needs cross-polarized Yagis with switching or a phasing system, or receive with both polarizations and use software that can combine or choose between them. On 70 cm the effect is much smaller, and on 23 cm and above it is usually negligible, so the issue becomes circular versus linear and agreeing the convention with your partner.

For checking the station, measuring Sun noise is the standard approach for evaluating the receive chain, and Moon noise follows as you get better. If your Sun noise numbers are far from what your gain and system temperature should give, fix that before you spend weeks chasing weak calls. Tracking errors, a badly placed feed, hot LNAs and a leaky transmit-receive relay are all typical culprits.

  • Moderators

On skeds, a few habits save a lot of failed attempts. First, work out the mutual window: both stations must have the Moon above their usable elevation at the same time, and the useful part is often much shorter than the Moon's time above the horizon at either end. Second, agree on the band, mode and submode, the frequency, the Doppler convention, and which station uses the first period. Don't leave those to be sorted out on the air, because mismatched periods waste whole minutes. Third, agree what to do if one side doesn't hear the other, such as repeating a fixed number of cycles and then moving to the next sked.

For Doppler, set the software to the same convention. Doppler shift is in the hundreds of Hz on 2 m, several kHz on 23 cm and tens of kHz on 10 GHz, and a mismatch of a few hundred Hz may be larger than the decode range. Many operators transmit with their own Doppler pre-correction in the WSJT-X controls so that the partner hears them on the nominal frequency, and the Echo tool provides a good test to confirm that the correction is right before the sked starts.

On the Q65 and JT65 choice, the decision often comes down to what your partner is running. Q65 offers advantages when there is a lot of spread or fading, and it has useful averaging features, but if the other station only has JT65 then that settles it. Large stations may also still use CW at a high enough signal level. For your first few schedules, pick a larger station with a well-known signal, since this tests your chain from the receive side before you have to prove your transmit side.

Finally, for the Moon-tracking side, trust the software but verify the pointing with the Sun or Moon noise, and keep a log of any azimuth and elevation offsets. On a dish for 10 GHz an error of a fraction of a degree will cost you the whole path.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.