Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field comms power and antenna planning: where do 24-hour deployments usually fall apart?

ci_cover.jpg

I'd like to compare notes on a basic field station design for a roughly 24-hour deployment, such as an EMCOMM shelter support role, a served-agency net control position, or a remote relay point. Assume an HF rig, a VHF/UHF mobile, a laptop for logging and digital modes, and a few small accessories. The question is what to plan around so the station keeps working after the first few hours.

Here is a framework to critique. Most failures seem to come from four places: power budget errors, bad connections, RF noise, and antenna support. The radios are rarely the problem.

Power budget first. Work in watt-hours, not amp-hours, so the numbers are comparable across systems. A 100 W HF rig at 100 W output can draw 20 A or more on transmit, but at typical net duty cycles the average draw is far lower. Receive current on many rigs is around 1 to 3 A. Add the laptop, a USB hub, lights, a charger for handhelds, and any amplifier or tuner. Estimate transmit and receive time separately, add 25 to 30 percent margin, and compare the result to usable battery capacity. A 100 Ah LiFePO4 battery is nominally about 1280 Wh, and you can use most of it, but check your battery's low-voltage cutoff against the lowest voltage your radio tolerates.

Voltage and cabling. Many 13.8 V radios are specified for 13.8 V DC plus or minus 15 percent, but check your own manual. A LiFePO4 battery usually sits around 13.2 to 13.4 V for most of its discharge and reads higher at full charge, so it often suits these radios well. Voltage drop is the hidden problem. A long, thin run to the radio can sag enough on transmit peaks to cause distorted audio, reduced output, or a radio that resets. Keep the main run short and heavy, fuse close to the battery positive terminal, and use a consistent connector standard such as Anderson Powerpoles, with a documented polarity convention so borrowed gear doesn't get reversed.

Generators. An inverter generator is useful for recharging batteries and for loads you can't easily run from DC, but it is a noise source and a safety hazard. Place it well away from the shelter, downwind, with the exhaust pointing away from tents and people. Never run it inside or in a partially enclosed space, because carbon monoxide is a real risk. Use a proper outdoor-rated cord with enough gauge for the length, and keep fuel stored separately and safely. Many operators prefer to run the generator to charge the battery bank and then shut it off, so the generator isn't a continuous noise source while the station is operating.

Solar. Solar works best as a trickle supplement or daytime top-up, not as your only source for a busy station. An MPPT controller usually harvests more from a given panel than a PWM controller, especially when panel voltage is well above battery voltage. Make sure the controller has a LiFePO4 charge profile or a configurable one. Also check the battery's low-temperature charging limits. Many LiFePO4 batteries should not be charged below freezing unless the battery has heating or a BMS that blocks charging, so read the spec sheet for your battery.

Noise. Switching power supplies, cheap DC-DC converters, USB chargers, LED lighting, and solar charge controllers are common sources of HF noise. A practical approach is to power up one device at a time while listening on a quiet band and note which ones raise the noise floor. Then separate the offenders physically from the antenna and feedline, add ferrite where it helps, and swap out the worst lights or chargers. A common-mode choke at the feedpoint and again near the radio often helps with feedline radiation and noise pickup, especially with a vertical or end-fed system.

Coax and feedline. Loss depends on frequency and cable type. Thin RG-58 style cable is fine for short HF runs but can waste a meaningful part of your signal at VHF/UHF over 50 to 100 feet. Use the manufacturer's loss tables for your actual cable and frequency, and don't rely on rules of thumb. Keep jumpers short, weatherproof outdoor connectors, and make strain relief part of the setup, since a cable pulled by a tripped person can destroy a connector or a radio port.

Masts and antennas. Pick a location with the mast's fall zone in mind, and keep well clear of overhead power lines. As a general rule, the distance to any line should be greater than the full height of the mast plus the antenna, and farther if you can manage it. Use guying appropriate to the mast and the expected wind, and use stakes or ballast rated for the ground conditions. If thunderstorms are forecast or nearby, plan to lower antennas and disconnect feedlines rather than trying to rely on grounding at a temporary site.

Grounding. Field grounding is often misunderstood. A single ground rod does not make a temporary station lightning-safe, and it can create a path you didn't intend. What it does provide is some static bleed-off and a reference point for equipment bonding. If you use a generator, follow the manufacturer's instructions on grounding, because many portable inverter generators have a bonded neutral-to-ground arrangement and the correct grounding approach depends on the model. Never backfeed a building or any other circuit from a generator without proper transfer equipment installed by a qualified person.

Shelter. Plan the layout before the tent goes up. Keep radios and batteries off the ground and away from wet edges, keep a clear cable path through doors, and use a drip loop on every cable entering the tent. Keep the operating position away from the generator and its exhaust, with enough light and ventilation to keep operators comfortable for hours.

Checklists. A setup checklist might run: confirm site safety and overhead hazards, place generator and fuel, lay out power distribution, erect mast and antennas, route and strain-relieve feedlines, bond equipment, connect batteries last, power up each device one at a time, check SWR and noise, then test communications. Teardown reverses it: shut down radios, disconnect power, lower antennas, coil cables in a consistent way, count the gear against an inventory, and check the site before leaving.

What would you change in this? In particular, I'm curious about preferred fuse and distribution layouts for a multi-radio station, and where people place the line between a decent field improvisation and gear that should stay home.

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One addition on power distribution: build it so a single failure doesn't take down the whole station. A common layout is a main fused feed from the battery to a distribution block, then separately fused branches for each radio, one for the computer and accessories, and one for lighting. That way a shorted light fixture can't drop your HF rig. Label each branch with its fuse rating and what's connected, because during a busy deployment nobody wants to trace wires.

Also check the BMS limits on the LiFePO4 battery. Some drop out on over-current or low voltage with no warning, and a transmit surge into a marginal cable can trigger that. If your main battery has a continuous discharge limit, compare it against the worst case of all connected loads, not just the radio. A multimeter and a clamp meter are worth carrying so you can see real current rather than guessing.

  • Moderators

On noise, I'd add a systematic order of operations. Start with the receive-only baseline: radio on battery, antenna connected, nothing else powered nearby. Note the S-meter or noise level on a couple of bands. Then add one item at a time: laptop, charger, charge controller, lights, and finally the generator if it's running. That makes it much easier to identify which device is the culprit, and it gives you a documented baseline for next time.

For the antenna side, don't underestimate the importance of separation. Moving the antenna farther from the operating position and putting the feedline through a choke often does more than any filter added at the radio. And if the noise is coming from the solar controller, try a different cable routing before you decide it is hopeless, since the panel wiring can act as part of an antenna. If the deployment is public service, keep a simple fallback plan too: a VHF/UHF handheld with a spare battery and a simple external antenna can keep a basic link up while you troubleshoot HF.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.