Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

How do you decide if a band is worth trying? SFI, K index, WSPR and beacons compared

ci_cover.jpg

Most of us start with the same numbers: solar flux (SFI), A index and K index. Those numbers only tell part of the story, and I'd like to compare how people use them alongside real-time tools.

Here is how I understand the basics, so correct me where I'm off.

SFI is the 10.7 cm solar radio flux. It is a convenient proxy for the ionizing radiation that builds the F layer. Higher SFI generally means a higher MUF, which is why 15, 12 and 10 m come alive near the top of the sunspot cycle. At the low end of the cycle the upper bands can go quiet for days. SFI is a trend indicator, though. It won't tell you whether Japan is open from your QTH right now.

The A index is a daily summary of geomagnetic activity. The K index is a 3-hour measure on a 0-9 scale, and Kp is the planetary version. Elevated K tends to hurt high-latitude and polar paths first, and a geomagnetic storm can also depress the F2 MUF at mid-latitudes. A quiet geomagnetic field doesn't guarantee good DX, but a disturbed one is a good reason to expect trouble.

Then there's the D layer. It forms only in daylight and absorbs lower frequencies, which is why 160, 80 and 40 m are mostly short-range by day and open up after sunset. A solar flare can cause a sudden spike in D-layer absorption on the sunlit side of the Earth, so the HF bands fade abruptly even when the SFI looks great.

For the path itself, the F layer MUF depends on layer ionization and on takeoff angle. A common rule of thumb is to work at or a little below the MUF, since signals near it are strongest and above it they escape. That's where VOACAP comes in. It's useful for planning because it models monthly median conditions from a smoothed sunspot number. It can show you which hours a path is likely open. It won't tell you about today's flare or a sporadic E cloud.

For real-time checks I lean on:

- WSPR spots, which show who is hearing whom at very low power on a given band right now.
- The NCDXF/IARU beacon network on 14.100, 18.110, 21.150, 24.930 and 28.200 MHz, which cycles through stations on a fixed schedule with a power step-down, so you can judge how marginal a path is.
- Reverse Beacon Network and PSKReporter spots for CW and digital modes.

Then there are the special cases. Sporadic E, which mostly shows up in summer at mid-latitudes, can open 10 m and 6 m, and sometimes 2 m, with no help from the SFI. Tropospheric ducting is a different mechanism for VHF/UHF, driven by temperature inversions and high-pressure weather. Gray line enhancement along the day/night terminator can help low-band paths. NVIS is a close-in propagation mode using high takeoff angles, typically on 80, 60 and 40 m, depending on the foF2 at the time.

So the question: when you're deciding where to point your effort for the evening, what's your order of operations? Do you check numbers first, or go straight to WSPR and beacons and trust what you see on the map?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd go to spots first and numbers second, because the spots are measurements and the indices are indirect indicators. If I check 20 m or 15 m and the beacon network shows several stations at decent strength, I don't need the SFI to tell me the band is open. The indices matter more when I'm planning ahead or trying to work out why something is behaving oddly.

One caution on WSPR: it shows what is possible with a low-power transmitter and a good receiver, not what your own station can work. A 200 Hz-wide decode at around -25 dB SNR means the path exists, but an SSB QSO needs a lot more signal than that. A useful trick is to run WSPR with something close to your normal power and antenna. Then the spot reports tell you more about your own setup, not just about the band.

For the NCDXF beacons, the four power steps are handy. If you can hear the 100 W transmission but not the 10 W one, the band is open but weak. If you hear all four, it's really open. It takes only a few minutes of listening to learn something useful.

  • Moderators

I'd add that the right tool depends on the band. HF is mostly about the ionosphere and the numbers you listed. Above about 50 MHz, a lot of the best openings come from other mechanisms, and SFI is almost irrelevant for them.

Sporadic E on 6 m is the classic example. The Es season in the northern hemisphere peaks around early summer, with a smaller peak around midwinter. You can't predict a specific opening from the solar flux, so spots, a cluster and the occasional beacon in the 50 MHz beacon segment tell you far more. Tropo is similar. It follows the weather map, and in a strong inversion, 144 MHz and 432 MHz paths can stretch well beyond line of sight, especially near coasts or across water.

On the lower bands, K index and absorption tell you more than SFI. On a quiet night at solar minimum, 160 and 80 m can be excellent even when the upper bands are dead. A low sunspot count helps on the low bands because there's less daytime D-layer absorption, and the F layer still supports good long-distance paths after dark.

For NVIS the question is whether your chosen frequency is below foF2. If the layer has weakened at night, 40 m can go long, and you may need 80 m to cover the same local area. If you use VOACAP for this, set the takeoff angle high and look at the lowest usable and maximum usable frequencies. Treat the answer as a starting point, then confirm with a test contact.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.