Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building wire antennas from scratch: what actually matters (wire, balun/choke, supports, SWR, modeling)

ci_cover.jpg

This thread is meant as a working checklist for anyone building a dipole, vertical or wire antenna from raw parts rather than buying a kit. Corrections and additions are welcome, especially where you disagree on numbers. I'll use a 40 m dipole as the example, but most of this scales to other bands.

Starting length. The usual formula for a half-wave dipole in free space is about 468 / f(MHz) feet, or 143 / f(MHz) metres, overall. Treat it as a starting point only. Height above ground, nearby trees and structures, wire diameter and insulation all shift resonance. Insulated wire typically resonates a few percent lower than bare wire because of the dielectric loading, so a cut length that works for bare copper will often be too long for PVC-jacketed stranded wire. Cut long, fold the ends back or leave extra length at the end insulators, and trim in small steps while measuring.

Wire choice. For spans that carry real tension, copper-clad steel (Copperweld type) resists stretching, which matters because a stretched dipole drifts off frequency. Hard-drawn copper at 14 AWG is a common compromise for long runs. Stranded copper, 14 AWG or finer, is easier to handle and suits sloper or portable use, but it stretches and can kink. Very thin wire (around 18 AWG or less) works electrically for QRP, but it is fragile in wind and ice and slightly narrows bandwidth. The extra resistive loss in a dipole is small compared with the cost of a broken span.

Insulators and supports. Anything non-conductive and UV-stable will do for end insulators: ceramic, acrylic or plastic dogbones, or even drilled PVC. Tie the wire through the hole and twist it back on itself, with strain relief so the solder joint or crimp at the feedpoint isn't carrying the load. Use UV-rated rope or polyester line for the halyard, not cotton. At the centre, take the weight of the coax off the connector with a strain-relief loop or a hook on the insulator. For an inverted V, the apex support carries the feedline weight and the legs set the angle. A shallower included angle raises feedpoint impedance towards 50 ohms at around 120 degrees, and a flat-top dipole is closer to 70 ohms.

Balun or choke at the feedpoint. A dipole is a balanced antenna. A coax feedline is unbalanced. Without something to stop it, common-mode current flows on the outside of the coax shield. That can distort the pattern, put RF in the shack and make SWR readings change as you move the cable. A 1:1 current balun or a common-mode choke at the feedpoint is cheap insurance. A simple choke can be coax turned into a coil of about 8 to 10 turns around a form, or several ferrite cores slipped over the cable. Ferrite mix matters: type 31 is generally preferred for lower HF and type 43 for the upper bands, but don't rely on a rule of thumb. Check the data sheet, or measure the choke's impedance with an analyzer. A choke impedance of a few thousand ohms at the operating frequency is a typical goal.

Ladder line. An open-wire feedline (450 ohm window line or homemade) has low loss even at high SWR, so a non-resonant doublet fed with ladder line and a tuner can cover several bands. The rules are simple: keep the line balanced and symmetrical, avoid running it parallel to metal, keep it clear of the ground, use a tuner designed for balanced lines (or a good 4:1 or 1:1 balun and a tuner), and use a choke where the line transitions to coax. At the transition, don't assume the balun is the only thing keeping the feedline balanced.

Fiberglass poles. Telescoping fiberglass poles are the easy way to get a vertical wire or an inverted-L up. Check for sections that don't lock, and expect sag when the pole is fully extended with a wire load. Carbon fiber poles are not interchangeable with fiberglass. Carbon is conductive and can detune or couple to the antenna. Keep any pole well away from power lines, regardless of material.

Verticals and radials. A quarter-wave vertical is around 234 / f(MHz) feet for the radiator. The radial system is part of the antenna. With an ideal ground, the feedpoint resistance of a quarter-wave vertical is about 36 ohms, so some builders droop the radials, which raises the impedance towards 50 ohms. Elevated radials (a few resonant quarter-wave ones, about 2 to 4 per band) can perform well because the ground loss is minimised. Radials directly on or in the ground need many more (a dozen or more, and more is better) to reduce loss. Put a choke at the base to keep the coax from acting as an extra radial.

Trap antennas. A trap is a parallel LC circuit that is resonant on a band, which isolates the outer wire on that band so one antenna can work on two or more. Traps add loss, reduce bandwidth and shorten the elements. They are also difficult to build at home because the capacitor ratings, coil form and weatherproofing all matter. If you can accept more wire, a fan dipole (separate dipoles on a common feedpoint) is simpler, and it is easier to tune. Note that interaction between elements shifts resonances.

Measuring SWR. Measure at the feedpoint, or at the end of the coax, with an antenna analyzer or a VNA. An SWR meter at the transmitter reads lower than the antenna's actual SWR when the coax has loss, which can mask a problem. Sweep across the band instead of reading a single frequency. The point of lowest SWR is usually close to, but not always exactly at, resonance, and a reading of 1.5:1 across a band is fine in most cases. If readings change when you touch or move the coax, you probably have common-mode current. Fix that first, then trim.

Modeling. EZNEC (NEC-based) and MMANA-GAL (MININEC-based) are both useful for the 'what if' questions before you cut wire: how much does height change the pattern, what does a drooping radial angle do to impedance, how much does a trap or loading coil shorten the antenna. Some habits help. Keep segments reasonably short (the usual guideline is under about a tenth of a wavelength, with more near the junctions and bends), check the ground type and height, use real wire conductivity and diameter, and treat the numbers as predictions to be checked against a measurement, not as the answer. Modelling radials and ground losses is the weakest area in both programs, so don't be surprised if the real performance differs.

Questions for the thread: what do you cut first, the wire or the pole? Do you trust a choke you haven't measured? And how many radials do you consider the minimum for a ground-mounted vertical?

  • Replies 2
  • Views 48
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

On the choke question: measure it if you can. A ferrite choke with a stated mix can still be poor for your band, because the impedance depends on the number of turns, the core size and the frequency. Putting turns of coax through a core adds capacitance between turns, which can pull the peak impedance down in frequency. For 40 m and below, a stack of type 31 cores or a single large toroid with a handful of turns often works better than a few beads. If you have an analyzer, put the choke on a short test lead and compare the reading before and after. A choke that looks fine on 40 m might be marginal on 10 m, and for a multiband antenna you may want two different chokes, or one at the feedpoint and another a quarter wave or so down the line.

For the radial minimum, it depends on the layout. Elevated and tuned: 2 to 4 per band is a defensible floor. On the ground or buried: I'd consider 16 a reasonable starting point and more worthwhile. The difference shows up as efficiency, and it can be hard to see from SWR alone, since poor ground loss often makes the SWR look good. An antenna with a nice 1.1:1 match may simply be a good dummy load.

  • Moderators

One addition on modeling and trimming. The model tells you the order of magnitude and the direction of change, not the final length. If the model says the dipole is resonant at 7.1 MHz at 12 m high and your measured resonance is 6.9 MHz, don't conclude that the model is broken. Check the real wire (insulated or bare), the actual height and sag, the end insulators and nearby objects. Then correct the model so that it matches the measurement and use that corrected model for the what-if work.

Also a note for the models themselves. In EZNEC you can check the average gain test to see whether the segmentation and ground setup are sensible. A result well away from 1 (0 dB) in free space means something is wrong with the geometry. MMANA-GAL is convenient for quick checks of a vertical with radials, but its ground treatment is simpler, so be careful with close-to-ground radials, and consider comparing the two programs on the same design.

On trimming: if you plan to use ladder line and a tuner, resonance matters less, and you can cut the wire to a length that avoids a very high impedance on the bands you use. A random length of the total doublet, say a half wave on the lowest band, is generally a safer choice than a length that is an exact multiple of a half wave on a higher band. Use a model, or a tuner-impedance check, before you cut.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.