Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Building clean CW: paddles, timing, filters and when to trust a decoder

ci_cover.jpg

This thread is for comparing notes on the parts of CW operating that tend to decide whether a QSO is comfortable or a struggle: the key, the timing, the receive setup, and how much help to take from software. Here are a few questions to get started.

On sending, are you using an iambic keyer with squeeze keying, a single-lever setup, a straight key, or a bug? Iambic keying has two common behaviors. In Mode A, the keyer stops when you release both paddles. In Mode B, it sends one more opposite element after release. The difference is only a few elements, but it affects letters like C, K, R and Q, so the keyer mode should match your habits. Paddle adjustment matters too: contact gap and spring tension change how often you send extra dits or dahs by accident. Whether the paddle is from N3ZN, Vibroplex, or somewhere else, a lot of sloppy sending comes down to setup, not the operator.

On receiving, how do you handle practice? Many people use Farnsworth timing or the Koch method, which sends each character at a fairly high speed (often around 18 to 20 WPM) while stretching the gaps between characters and words. The point is to learn the sound of each character as a whole pattern, not to count dits and dahs. The gaps are then shortened as copy improves.

For the receiver, what filter width and sidetone pitch do you settle on? And where do you draw the line on CW Skimmer, Reverse Beacon Network spots, and decoders: spotting tool, training wheels, or both?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the filter question, the usual advice is to use the widest filter that still gives you clean copy. A 200 Hz filter can sound great on a crowded band, but it also hides callers who are a little off frequency, and a very narrow DSP or crystal filter can ring on strong signals, which makes characters smear together. Something around 300 to 500 Hz is a common starting range for general operating. Tighten it when QRM requires it, and widen it again when you're searching or running a pileup.

Matching your sidetone pitch to the receive pitch helps more than people expect. If your sidetone is at 700 Hz but you tune stations in at 500 Hz, you are making zero-beating harder than it needs to be. Pick a pitch that is comfortable for long sessions and keep it consistent across the radio, the keyer, and any logging or skimmer software.

QSK is worth trying if your rig supports it properly. Hearing the band between your own elements lets you notice someone calling you, or a station already on frequency, without waiting for a hang-time delay. It does depend on the equipment, though. Some amplifier and relay combinations can't keep up with full break-in at higher speeds, so semi break-in with a short delay is a sensible fallback.

  • Administrators

On decoders, I would treat them as a spotting aid rather than a substitute for copying. CW Skimmer can decode many signals across a band at once, which makes it very useful for seeing who is active, especially during contests. But the output depends on clean timing and a decent signal. QSB, QRN, a heavy fist, or two stations overlapping can produce confident-looking text that is simply wrong. Using the decoded callsign to find the station, then confirming it by ear, is much more reliable than copying a whole exchange from the screen.

For contest work, I would build on a few specific habits. Learn the cut numbers used in the exchange (for example, N for nine and T for zero) so you aren't thinking about them while the pileup builds. Send at a speed you can also copy when the other station replies at that speed. Use AGN, a repeated callsign, or a single number only when you truly need it, and keep the exchange short and consistent. Practice with a contest simulator or recorded pileups, because copying a callsign in a pileup is a skill you won't get from ragchewing.

On the abbreviations and prosigns: AR ends a transmission, SK ends a contact, KN invites only the station you are working to reply, and BT separates parts of a message. Learn them as single sounds, not as letters sent together, and your sending will sound more natural, whatever key you are using.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.