Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

VHF/UHF antenna choices: J-pole vs 5/8 whip vs collinear vs yagi, and where coax, connectors and SWR fit in

ci_cover.jpg

This thread is for sorting out what matters when you pick and install a VHF/UHF antenna. Most of the arguments come from mixing up gain, pattern, feedline loss and mounting, so here is a baseline to push back on.

Start with the basic omni antennas. A quarter-wave whip is about 19 inches long on 2 m and roughly 6.5 inches on 70 cm. It needs a ground plane, such as a vehicle roof or a set of radials, and it has a fairly low-angle pattern with roughly unity gain over a ground-plane reference. A 5/8-wave whip is longer and usually has a loading coil or matching network at the base. It concentrates a bit more energy toward the horizon, and the commonly quoted benefit is a few dB over a quarter-wave. That figure depends heavily on the ground plane, and a 5/8 wave on a small or off-center ground plane can disappoint.

The J-pole and slim jim are both end-fed half-wave antennas with a quarter-wave matching section. They are easy to build and tolerate rough conditions, but their gain is about that of a half-wave dipole, so don't expect big numbers from the shape alone. Because they have no true radial system, the outside of the coax can become part of the antenna. A choke or a few ferrite beads, or coiling the coax into a choke near the feedpoint, can keep the pattern from getting distorted.

Collinears stack phased half-wave sections to squash the vertical pattern. This gives more gain toward the horizon, but the beam gets narrower in elevation. That is great for a flat-terrain repeater or a base station talking to distant stations. It can be worse if you are on a hill and want to reach stations well below you. Keep any collinear well clear of the mast, because a metal mast right next to the radiating elements will distort the pattern.

Yagis are the right choice when you know where the other station is. A few elements give a good improvement over an omni, and long-boom designs go further. Keep dBd and dBi straight, because they differ by 2.15 dB. A manufacturer quoting dBi will look about 2 dB better than the same antenna quoted in dBd.

So the questions for discussion: when would you pick a gain omni over a small yagi on a fixed station, and which of these antennas do you think are most often oversold on their gain?

  • Replies 2
  • Views 49
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd add that the feedline and connectors can cancel out the choice of antenna, especially on 70 cm. Loss in coax rises with frequency, and small-diameter cable like RG-58 can eat a large share of your power over a long run at UHF. Check the manufacturer's datasheet for loss per 100 ft at your frequency instead of trusting generic tables. Low-loss cables like LMR-400 type or hardline are far better for runs of a few tens of feet or more. For a short mobile run, thinner coax is fine.

On connectors, PL-259/SO-239 (UHF) connectors are common and work well enough on HF and often on 2 m. They are not constant-impedance and they aren't weatherproof by design, so they get worse at 440 MHz and above. N-type connectors are a 50 ohm design, have a gasket for weather sealing, and are much better for outdoor UHF and base or repeater installs. Whichever you use, seal outdoor connections with self-amalgamating tape and then a layer of vinyl tape, and form a drip loop so water doesn't run down the cable into the shack.

On SWR: it tells you about the match, not about how well the antenna radiates. A dummy load has excellent SWR and radiates nothing. Also, long, lossy coax can make SWR look better than it actually is at the antenna, because the loss attenuates the reflected power on its way back. If you want to check the antenna itself, measure with a short known-good jumper, or at the antenna end of the feedline if possible.

For mobile installs, an NMO mount through the roof gives the most reliable ground plane and keeps the whip centered. A magnetic mount is easier and non-destructive, but it relies on capacitive coupling to the body and can vary a lot with the surface and how clean the contact is. Mount magnetic bases on a flat area of the roof, away from the edges, and avoid putting them on trunk lids or places where the ground plane is small.

  • Moderators

Polarization is the other thing that catches people. FM simplex and repeaters on VHF/UHF are almost always vertically polarized, so a vertical antenna on the mobile or handheld side is the match. If you put a horizontal yagi against a vertical station you can lose around 20 dB or more in the ideal case, though real-world reflections and multipath reduce that. Weak-signal work on 2 m and 70 cm (SSB and CW) is usually horizontal, so a yagi for that purpose is mounted with the elements horizontal. If you want to do both, use two antennas or a rotatable one that can be switched, instead of expecting one antenna to do both jobs.

Satellite work changes the rules. Many satellite signals are circularly polarized, or can appear to rotate as the satellite tumbles or the geometry changes. A linearly polarized antenna on the ground will see fading as the polarization changes. A crossed yagi, with two sets of elements fed with a phase shift, gives circular polarization and handles this better. Many FM satellite operators get by with a handheld and a small directional antenna like a handheld yagi or arrow-style antenna, but you do need to track the satellite and account for Doppler shift, since the frequency changes over a pass. Check current satellite frequencies and operating modes from an up-to-date source, since they change over time.

For repeaters, the usual setup is a gain omni such as a collinear, high up, with a duplexer so the transmitter and receiver share the same antenna. The alternative is two antennas separated vertically to get isolation. Either way, the key issue is keeping the transmitter from desensitizing the receiver, so feedline quality, connector quality and antenna placement matter more than they do on a simple base station. Make sure lightning protection and grounding are in place before the antenna goes up, because tall antennas tend to be the highest point in the area.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.