Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Field deployment layout: keeping generator and solar noise out of the receiver while staying safe on power and grounding

ci_cover.jpg

I'm sketching a standard layout for a portable HF/VHF station that could be used for EMCOMM support or a long field day: a 100 W HF rig, a dual-band VHF/UHF radio, a laptop for digital modes, and a few small loads like lighting and a charger. Power options would be a LiFePO4 battery, a small inverter generator as backup, and a folding solar panel to extend battery runtime. Antennas would be a mast-mounted vertical or an inverted-V on a fiberglass pole, plus a VHF/UHF antenna on its own mast.

The question is how to arrange all of this so the stations work well and nothing becomes a hazard or a noise source. Here are the points I'd like feedback on.

First, noise. Inverter generators put out clean AC, but the electronics and the cable run can still radiate hash on HF. Solar MPPT charge controllers are also known to make broadband noise on some bands. What distance and cable-routing rules are reasonable starting points, and how do you check for noise before you commit to a layout?

Second, power distribution. A 100 W HF rig can pull roughly 20 A at 12 V on transmit peaks, so wire gauge, fusing and connectors matter. I was thinking of a fused distribution block near the battery, Powerpole connectors, and short, heavy runs to the HF rig, with lighter circuits for everything else. Is there anything you'd change?

Third, grounding and safety. I want to separate lightning and shock safety from RF grounding in my head. A ground rod isn't lightning protection for a field station, and it won't necessarily cure noise. I'd like to hear how others handle equipment bonding, generator grounding, and the rule for when to take down antennas and disconnect coax if a storm is approaching.

Finally, the physical layout: where the tent or shelter goes relative to the generator, the mast, and the coax runs, and what belongs on the setup and teardown checklists.

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

For noise, treat it as something to measure rather than assume. Before connecting the antenna to the main station, tune the HF rig to a quiet spot on a few bands, such as 80/40 m and 20 m, with the radio on battery only and everything else off. Note the S-meter reading or noise floor. Then turn things on one at a time: laptop, charger, solar controller, then the generator. The thing that raises the noise floor is your culprit, and you'll know exactly what to fix. Common fixes are ferrite clamps on DC leads and USB cables, moving the controller or charger farther from the antenna and feedline, and swapping a noisy supply for a different one. Some MPPT controllers are noisier than others, and some PWM controllers are quieter, so if solar noise is a problem, try disconnecting the panel or controller while operating. Running on the LiFePO4 battery and charging between sessions is a legitimate way to keep the station quiet.

The generator should be well downwind, as far as the extension cord and the layout allow, and never anywhere near the tent. Carbon monoxide is the real hazard, and exhaust can drift into a tent or shelter, so use a CO alarm in occupied enclosed spaces. Refuel only with the engine off and cool, and keep fuel away from the operating area. Also, use the generator's own outlets as the manual instructs. Don't backfeed anything, and check whether your unit's neutral and ground are bonded before relying on a GFCI or an extra ground rod, because the manual will say what is correct for that model.

On coax, put a common-mode choke, whether a 1:1 current balun or a ferrite choke, at the feedpoint of any antenna, and consider another one at the radio. This helps with both noise pickup and RF on the shield. For VHF/UHF, feedline loss really matters over long runs, so use a low-loss cable such as LMR-400 or similar rather than thin RG-58, which loses noticeably more at 146 MHz and 446 MHz over 50 to 100 feet. For HF, loss in typical runs is much less of a concern than at VHF, so a thinner, more flexible cable is often fine.

  • Administrators

On power, I'd start from the loads and work backward. List every device, its current draw on receive and on transmit, and how long it will run. For 12 V systems the usual approach is a fused feed directly off the battery, then a distribution block with an individual fuse for each branch. Size the wire for the fuse and the length of the run so that voltage drop under transmit stays small. Many rigs misbehave or lose output if the voltage sags at the radio, so measure at the radio's terminals under transmit, not just at the battery. A LiFePO4 pack holds its voltage well during discharge, but check the radio's operating range, since a fully charged pack sits above 13 V. Most rigs tolerate that, but not all accessories do. Also don't charge LiFePO4 below freezing unless the pack has low-temperature charge protection, because that is a known way to damage cells. Cold weather matters for this reason.

On masts and antennas: keep guy lines flagged so people don't walk into them, and keep the whole antenna system well clear of power lines. A common rule of thumb is to stay at least one and a half times the mast height away, but the safest approach is to pick a spot where the question never comes up. Fiberglass poles are popular because they don't conduct, though a wet pole isn't a reason to get complacent. Account for wind: use proper guying, stakes sized for the soil, and a plan for lowering the mast if the weather changes. Tents and shelters should be placed so that, if the mast fell, it wouldn't land on the operating position. Keep VHF antennas away from the HF antenna's near field and from the operators.

A basic checklist structure that works for both setup and teardown: site survey and hazards first (power lines, ground, wind, access), then shelter and generator placement, then the mast and antennas, then the coax and power runs with strain relief and drip loops, then the station itself, and last a pre-operation test including a noise check, SWR check, and a radio check with a net or another station. Teardown should run in reverse, with the antennas and mast lowered first, a headcount of stakes and cable, and the generator cooled before it's packed. Print it, laminate it, and revise it after each exercise. The first few runs usually show what the list is missing.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.