Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

SSB audio setup: mic gain, ALC, compression and bandwidth for clean signals and weak-signal DX

ci_cover.jpg

Here is a checklist for setting up SSB transmit audio, with the reasoning behind each step. The goal is a signal that is easy to copy under poor conditions, not one that just sounds loud on the meter. Corrections and additions are welcome.

1. Start with the microphone and how you use it. Everything downstream depends on the mic. A dynamic mic or headset with a limited, speech-focused response is usually the easiest choice for HF, because it picks up less room noise and needs less equalizer work. A large-diaphragm condenser can sound excellent, but it also picks up fans, keyboards and room reflections, and the processor will raise all of that along with your voice. Keep your mouth at a consistent distance, typically a few centimeters, and slightly off-axis to reduce plosives. A foam windscreen costs little and helps. Moving around in front of the mic changes your level more than any menu setting does.

2. Set mic gain by watching ALC, not the power meter. ALC (automatic level control) protects the transmitter from overdrive. It is not a loudness control. Set mic gain so that normal speech peaks just touch the ALC range your rig's manual calls the safe zone, and no further. If the ALC meter is pinned, the signal is distorted and splatter becomes likely, and the splatter lands on stations next to you. Remember that a speech peak is brief, so watch the meter while talking at your normal level, not while sustaining a vowel like "aaaah" or whistling.

3. If you use a speech processor, use it sparingly. Compression reduces the gap between loud and soft syllables, which raises average power without raising peak power. That helps in weak-signal work because the average level is what the other operator's ear and filter respond to. The cost is that more compression raises background noise, exaggerates sibilance and increases distortion. Many operators find a few dB of compression useful. Heavy settings often sound worse and can make a signal harder to copy, even if the receiving S-meter rises. Adjust the processor only after mic gain and ALC are right, and re-check ALC after enabling it, since many rigs interact.

4. Use the monitor function and listen critically. Turn on the TX monitor and listen on headphones so you do not get feedback. Check for harshness, a boomy low end, mouth noise and the pumping sound of excessive compression. Monitor circuits differ between radios, so it is a useful sanity check but not a perfect picture of what is on the air. Where possible, get a recorded or live report from a friendly station, or listen to yourself on a remote SDR receiver if one is available nearby.

5. Shape the audio with the equalizer and transmit bandwidth. Most intelligibility in speech sits between roughly 300 Hz and 3 kHz. Cutting very low frequencies reduces muddiness and wasted power. A gentle boost in the presence range, around 2 to 3 kHz, can improve clarity, but too much sounds sharp and tiring. A transmit bandwidth of about 2.4 to 2.7 kHz is a common compromise. A narrower bandwidth concentrates power into the most useful part of the voice and is courteous on a crowded band. A wider one sounds more natural for a casual chat when the band is quiet. Do not use extra width just because the radio allows it. Wide, heavily processed audio takes up more spectrum and is not always better for the listener.

6. Use the right sideband. By convention, LSB is used on 160, 80 and 40 meters, and USB on 20 meters and above. On 60 meters, USB is the convention in the channelized allocations. Operating on the wrong sideband makes you hard to copy for stations who tune a normal way. Be aware that nonstandard sideband use does exist in some local nets, so listen first.

7. On receive, a 2.4 kHz filter is a starting point, not a rule. A passband around 2.4 kHz suits normal SSB. When QRM is close by, narrowing to roughly 1.8 to 2.1 kHz, or shifting the passband away from the interferer with IF shift or passband tuning, often improves copy more than adding noise reduction. Use the notch for a carrier or tuner, and be careful with aggressive noise reduction, which can add artifacts that make weak speech harder to understand. Choose AGC speed to suit the conditions: fast for quick tuning, slower for fading signals without constant level jumps. On a quiet band, preamps may help. On a noisy lower band, extra gain often only raises the noise.

8. Working weak stations and DX. Clean audio beats raw power. An overdriven rig and amplifier can make a signal wider and harder to copy than a modestly powered clean one. Do not exceed your amplifier's drive requirements, and keep drive low enough to avoid flat-topping. Give call signs slowly and clearly, using standard phonetics, repeat key information, and keep transmissions short. In DX pileups, listen for how the DX station is working: split operation, geographic call areas or listing. Calling on their frequency when they are listening up wastes time and annoys others. Check your own signal quality before a long DX session so you are not troubleshooting during the pileup.

Questions for discussion: How do you set the compression level on your radio? Do you prefer a narrower transmit bandwidth for DX? And do you trust your rig's monitor, or do you check against an external receiver?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

Good list. One addition on ALC: some rigs have separate meters or settings for compression level and ALC, and it is easy to confuse them. Compression level normally shows how hard the processor is working, while ALC shows how close you are to overdriving the final stage. If your radio has a processor, set it in order: mic gain first with the processor off, then enable it and set compression, then check that ALC is still in range. Doing it in a different order often gives misleading readings.

On the equalizer, make small changes and test them one at a time. A big bass cut and a big treble boost together can leave a thin, harsh sound that looks fine on paper but is tiring to copy over a long QSO. If you aren't sure, a flat or mildly adjusted setting with a good mic position is usually safer than a dramatic preset copied from someone else's radio, because their mic and room are different.

  • Administrators

On the bandwidth question: narrower is not automatically better. A very narrow transmit passband can make speech sound muffled, and some listeners find it harder to understand, especially with accents or poor receive conditions. Something around 2.4 kHz tends to be a solid default, and you can narrow it a bit when the band is crowded or a pileup is running. The sensible test is a report from a station that can tell you how it sounds, rather than your own preference at the monitor.

On receive, I'd also say don't rely on a filter alone when the interference is right on top of the signal. Try shifting the passband, switching sideband briefly to see which side is cleaner, or lowering RF gain so strong nearby signals don't overload the front end. Those simple steps often help more than stacking noise reduction and notch filters.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.