Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Small lot, HOA, one band or many: which compromise HF wire antenna gives the best return? EFHW vs OCFD vs G5RV vs doublet

ci_cover.jpg

Here is a scenario that comes up constantly on the forums. A ham has a suburban lot, a roughly 60 to 70 ft run for a wire, one or two supports around 25 to 35 ft, and an HOA that frowns on anything that looks like a tower. There is no room for a beam. They want 80 or 40 through 10 m, a transceiver with an internal tuner, and minimal fuss. Which wire antenna do you pick, and why?

Let's compare the usual candidates on what they actually do, not just on what the SWR meter shows.

End-fed half-wave (EFHW). The feedpoint is at the end of a half-wave wire, where impedance is very high (a few thousand ohms). A 49:1 or 64:1 transformer brings it down to something a transmitter can use. A wire cut for 40 m also works on 20, 15 and 10 m because those are harmonics. The weak point is that there is no true balanced feed. The coax shield and the transformer case act as part of the antenna, so a poor common-mode choke or a feedline that happens to be a bad length can change the SWR and the noise level. The wire is also high voltage at the end, so keep it out of reach of people and pets.

Off-center-fed dipole (OCFD). This is a half-wave wire fed about a third of the way along, typically through a 4:1 current balun. It gives usable multi-band coverage on 80/40/20/10 m with odd patterns on some bands. It is a better-balanced system than an EFHW, but the match is only approximate, and you still need good choking at the feedpoint.

G5RV. This is a roughly 102 ft flat-top with about 34 ft of ladder line, then coax to the shack. It was designed around 20 m, where the antenna is about 3/2 wavelength, and elsewhere it is a tuner-assisted compromise. It works, but the coax often sees a high SWR on bands other than 20 m, and that costs you loss, especially if you use thin coax on the higher bands.

Doublet with open-wire or ladder line. A center-fed wire, ideally not an awkward length, with balanced line to an external tuner or a balun/tuner combination. It is the most flexible and typically the lowest-loss option on many bands, because balanced line loses very little even with a high SWR. The downside is routing: ladder line does not like to touch metal gutters or run close parallel to other conductors, and it has to come into the shack somewhere.

Inverted V. If you have one tall support, this is the easy way to get a dipole on the air. The ends droop, so the resonant length is a few percent shorter, and bandwidth and feedpoint impedance shift (usually toward 50 ohms, which is convenient). Try to keep the included angle at 90 degrees or more and keep the ends well above head height.

Two things I would like this thread to dig into. First, SWR is not efficiency. A dummy load is perfectly 1:1. What matters is radiation, feedline and transformer loss, and ground loss. Second, height above ground: a horizontal dipole below about a quarter wavelength tends to send more energy upward. That is fine for regional contacts on 40 or 80 m, but not what you want for DX on the higher bands.

What would you string up in this lot, and what would you measure to decide whether it is working?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I would lean toward the doublet, with a caveat. If you can run balanced line out the window or through a wall plate, a 60 to 70 ft center-fed wire with an ATU and a good 1:1 current balun at the transition can be a very capable multi-band antenna. The part people underestimate is what happens at the transition from balanced to unbalanced. If you use a balun ahead of the tuner, the tuner sees a high-impedance load on some bands, and the balun core can overheat or get lossy. Check the rating and the core size. If your tuner has a balanced output, or you use a dedicated balanced tuner, you skip that problem altogether.

For the EFHW fans: it is a perfectly good portable antenna and a good stealth option, since it needs only one support and a feed at the end. But treat the feedline as part of the antenna. A choke of at least several kilo-ohms of common-mode impedance on the coax near the transformer is cheap insurance. If the SWR changes when you move the coax, or your RF-in-the-shack symptoms follow the cable, you probably have common-mode current, not a mystery.

Also, measure with an antenna analyzer, not just the rig's SWR meter, and look at both SWR and the resonant points. If an "EFHW" has a decent SWR on every band but the signal reports are poor, suspect loss in the transformer or the feedline. You can test by temporarily swapping in a dummy load or comparing against a simple dipole at the same height.

  • Moderators

On the HOA side, it helps to read the actual CC&Rs before choosing anything. In the US, the FCC's PRB-1 limited-preemption policy covers state and local zoning rules, but it does not override private deed restrictions, so what applies to you depends on your covenants. Many covenants prohibit visible outdoor antennas but are silent about thin wire. Black or dark green 18 to 26 AWG insulated wire against a tree line is very hard to see. Wire along the top of a fence, or a vertical hidden as a flagpole, are other common approaches. If the covenants ban outdoor antennas completely, an attic dipole, an indoor loop, or a loaded vertical may be the only choices, and expectations have to be adjusted.

A caution about verticals and loops in small yards. A ground-mounted vertical lives or dies by its radial system. A quarter-wave vertical over only a few short radials loses a lot of power in the ground, even if the SWR looks great. Elevated radials, even four tuned ones per band, usually beat a small number of buried ones, and the feedpoint impedance behaves more predictably. A small magnetic loop is a different animal: narrow bandwidth, you retune it when you change frequency, and its efficiency on 40 and 80 m is limited by its size and by the conductor and joint quality. It can be a quiet receiver in a noisy neighborhood, so it is useful, but it is not a free lunch for transmit.

A practical way to compare: pick a band, use the same power, and check reports on something like WSPR, PSKReporter or RBN spots. It is not perfect, but it gives repeatable data between antennas. A coax check is also easy: on 10 m, RG-58 can lose a couple of dB per 100 ft, and a mismatch makes it worse, which can add up when the antenna is far from the shack.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.