Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dynamic range, noise and antennas: what limits an SDR setup more, the ADC or everything in front of it?

ci_cover.jpg

A common point of confusion when choosing between an RTL-SDR dongle, an Airspy, an SDRplay RSP or a HackRF is the spec sheet. ADC bit depth, maximum bandwidth and tuning range are easy to compare. Dynamic range, front-end filtering and the noise floor at your location are harder to compare, and they usually decide how the receiver behaves.

Some rough numbers to anchor the discussion. The RTL2832U in a typical RTL-SDR is an 8-bit converter. The theoretical limit for an ideal N-bit ADC is about 6.02 x N + 1.76 dB, so around 50 dB. Real dongles get less, and the tuner's own gain stages matter as much as the converter. 12-bit and 14-bit designs such as the Airspy R2 and the SDRplay RSP family have far more headroom, but only if the front end ahead of the ADC does not overload first. A strong FM broadcast station or a local medium-wave transmitter can push the tuner into compression and produce phantom signals across the band, even on a 14-bit receiver.

That raises a few practical questions for the thread:

1. For VHF/UHF work such as ADS-B, airband, APRS and NOAA satellites, is a broadcast-FM notch filter or a bandpass filter a better first purchase than a higher-resolution SDR?

2. For HF, when does direct sampling on an RTL-SDR stop being worth the trouble compared with an upconverter (commonly a 100 MHz or 125 MHz oscillator offset, entered as a frequency offset in SDR# or HDSDR) or a purpose-built HF receiver?

3. How much of the noise you see on the waterfall comes from the radio, and how much from USB hub noise, switching supplies, LED lighting and common-mode current on the coax?

4. Where should the LNA go, and when does adding gain hurt more than it helps?

Software choice also shapes the experience. SDR#, SDRuno, HDSDR, GQRX and CubicSDR all handle demodulation and waterfalls competently, but they differ in plugin ecosystem, supported hardware drivers (ExtIO, SoapySDR, gr-osmosdr) and CAT or rigctl integration for use as a panadapter. If you have a view on what worked for decoding digital modes or driving a bandscope next to a transceiver, say which hardware and OS you meant.

  • Replies 2
  • Views 35
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

In most setups the order of importance runs: antenna and location, then filtering, then gain staging, then ADC resolution. Bit depth is the last one. An 8-bit dongle with a sensible gain setting and a notch for the strongest local broadcaster can beat a 14-bit receiver that sits at maximum gain on a noisy antenna.

The gain rule is to raise it only until the noise floor in your passband rises a few dB above the receiver's own floor, then stop. More gain after that lifts the signal and the noise together and reduces headroom. If the waterfall shows spurs that move when you change gain, the front end is overloading. Those signals aren't real. Backing off the gain, adding attenuation or filtering is the fix. A cleaner ADC won't help.

On HF, the upconverter versus direct-sampling question depends on the band. Direct sampling on an RTL-SDR uses the converter without the tuner's mixer, so there is no gain control and no preselection. It is usable for strong signals on a decent antenna, but it overloads easily and aliasing is a risk without a low-pass filter. An upconverter with a proper filter keeps the tuner in its normal range, but check the LO offset. A 125 MHz converter puts 7.100 MHz at 132.100 MHz, and SDR# needs the offset set correctly or every frequency readout will be wrong. Receivers designed for HF, such as the Airspy HF+ or the HF ports of the RSP models, avoid the problem and generally have better large-signal behavior. They cost more, which is why the cheaper route stays popular.

  • Moderators

I'd put the noise question ahead of everything else, because it determines whether any of the above matters. A quick test is to disconnect the antenna and terminate the input with a 50-ohm load. That shows what the receiver and its USB environment contribute on their own. Then reconnect the antenna. If the floor jumps a lot, the noise is arriving through the antenna or the feedline, and a better SDR won't fix it. Common-mode current on the coax shield is a frequent culprit. A choke close to the receiver, ferrites on the USB cable, a short USB extension to move the dongle away from the computer, and powering things from a linear supply or battery are all cheap tests.

For antennas, a quarter-wave whip or a discone is fine for scanning VHF/UHF. Matching the antenna to the band matters more than gain. An ADS-B collinear or a 1090 MHz quarter-wave outdoors with short, low-loss coax usually does more than any software tweak, and a 1090 MHz bandpass filter with an LNA at the antenna helps if the feedline is long. For HF, small active loops and short whips give a low noise pickup from a balcony, while a longwire with a 9:1 unun brings more signal and more local noise with it. Either way, a bigger signal isn't the goal. The aim is signal-to-noise ratio.

For digital modes, the software chain is mostly routing. FT8 needs the demodulated audio sent to WSJT-X through a virtual audio cable (or a loopback device on Linux), and the receiver's frequency accuracy matters, so check the dongle's ppm correction or use a TCXO model. ADS-B and AIS decoders usually connect to the SDR directly, with no audio step. For panadapter use with a transceiver, CAT control through OmniRig or rigctl keeps the SDR display and the radio's dial in sync, but the signal still needs to be tapped from a splitter or the IF output, never from a transmit path without proper protection.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.