Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 412.9 km/s
Aurora 1
Updated 14:00 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

From-scratch wire antenna build checklist: materials, feedpoint choke, supports, and checking the result with an analyzer and a model

ci_cover.jpg

This thread is meant as a working checklist for building HF wire antennas from raw materials, plus a place to argue about the tradeoffs. The example is a center-fed dipole for 40 m with a possible upgrade to multiband, but most of it applies to inverted-Vs, fan dipoles, doublets and quarter-wave verticals too.

Wire. Hard-drawn copper or copper-clad steel in 14 AWG is the usual compromise for a permanent span. It is strong and stretches little, and the resistive loss is negligible at dipole lengths. Stranded insulated 14 to 18 AWG is easier to handle and coil, but the insulation lowers the resonant frequency, so expect to cut it a few percent shorter than the bare-wire figure. For a first cut, a half-wave dipole is roughly 468 / f(MHz) feet. At 7.1 MHz that is about 66 ft overall. Cut long, then trim. Height, nearby trees, sloping ends and wire type all move the resonance, so the formula is a starting point, not a final length.

Insulators and supports. Anything that survives UV and does not absorb water works: commercial ceramic or molded dogbones, cut HDPE or acrylic, even PVC offcuts. Mechanical strength matters more than electrical rating at HF power levels. For end supports, UV-stabilized polyester rope is the usual choice, and cotton or cheap polypropylene will rot or fray. Trees move, so a pulley with a counterweight or a length of bungee at one end keeps the wire from being pulled apart in wind. At the center, the coax weight should never hang on the connector. Use a center insulator with a strain-relief hole or a short tie-off loop so the pull goes to the wire and rope, not the SO-239.

Feedpoint choke. Feeding a balanced dipole directly with unbalanced coax lets current flow on the outside of the shield. That distorts the pattern, can put RF in the shack, and makes SWR readings depend on how the coax is routed. A 1:1 current balun, really a common-mode choke, at the feedpoint prevents it. Two common builds are a stack of ferrite beads over the coax, or a number of turns of coax wound through a large toroid or on a former. Mix choice matters. Type 31 is generally favored for the lower HF bands, and type 43 does better higher up. The goal is a common-mode impedance of at least a few kilohms across the band you care about, not a particular number of turns. If you have an analyzer, you can measure it with a simple test jig. For a doublet fed with ladder line, the 4:1 balun at the tuner end is a separate question from choking the feedline.

Ladder line. 450 Ω window line into a balanced tuner (or an unbalanced tuner with a good balun) lets one doublet cover many bands with relatively low feedline loss, even when the antenna is far from resonance. Keep it clear of metal gutters and downspouts, avoid tight bends, and bring it away from the antenna at a right angle for a few feet. Certain feedline lengths on certain bands produce very high voltage or very high impedance at the tuner, so changing the line length by a few feet can fix an otherwise unmatchable band.

Fiberglass poles. Telescoping fiberglass masts are an easy way to hold the center of an inverted V or to support a vertical wire. Collapse risk is at the top sections, which are the thinnest, so do not load them with a heavy balun and a lot of coax. Clamp or tape the sections where they overlap, never use one near power lines, and remember that it holds a wire antenna, not a guyless tower.

Verticals and radials. A quarter-wave vertical is about 234 / f(MHz) feet, so roughly 33 ft on 40 m. On the ground, performance depends heavily on the radial field. Many shorter radials usually beat a few long ones, and a field of a few dozen is common practice. Elevated radials are a different tradeoff. Four resonant radials can do well, and sloping them downward raises the feedpoint impedance toward 50 Ω. A vertical still needs a feedline choke, since the radials are not the same as a perfect ground.

Tuned versus trap antennas. Trap dipoles use parallel LC circuits to isolate outer sections at the higher band, which makes the antenna shorter but adds loss and narrows bandwidth. The inductor Q, capacitor voltage rating and weatherproofing all matter. A fan dipole, with separate wires for each band on a shared feedpoint, is easier to build and tune, though the elements interact. Tune from the highest band down, because trimming a lower-band element has less effect on the higher bands than the other way around.

Measuring. An antenna analyzer at the feedpoint, or at the end of a known length of coax, is better than an SWR meter at the transmitter. Look at resistance and reactance, not just SWR. The frequency where reactance crosses zero is the resonant point, and the SWR minimum can sit slightly off it. Coax loss can make a poor antenna look good, since the loss hides reflected power. And SWR is not efficiency. A dummy load reads 1:1.

Modeling. EZNEC uses a NEC engine and handles real-ground effects more credibly than MMANA-GAL, which is MININEC-based, free, and very convenient for quick shape and length work. The free EZNEC demo has a segment limit, which constrains complex models. Common mistakes include too few segments, mismatched segment lengths at junctions, leaving the ground at perfect when it should be real, and forgetting to set wire loss. A model will not tell you your absolute SWR with insulated wire and a nearby fence. It is best used to compare options, like height changes, sloper angle, or radial count, and then you confirm on the real antenna.

Where do people here draw the line between building it once and trimming, versus modeling first? And what is your preferred choke for a feedpoint on the lower bands?

  • Replies 2
  • Views 48
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On the choke, I'd push back a little on turns-count rules of thumb. Coax coiled into a loop of a few turns can work well on the higher bands, but at 80 and 40 m the inductance and stray capacitance between turns can leave you with a modest impedance. Winding on a ferrite core, or stacking beads rated for the band, is a more predictable route. If you have an analyzer, you can check a choke by measuring its impedance on a short test jig and not relying on the build recipe.

Another thing to watch with ladder line: even a perfectly balanced doublet can show common-mode current if the feedline is run asymmetrically near a wall or a mast. A choke at the tuner end helps there too, and it can calm down RF-in-the-shack issues that look like an antenna problem.

  • Moderators

On modeling first or building first, it depends on what the question is. For a simple dipole, cut-and-trim is quicker than modeling it. For asking something like how much a sloping radial angle changes feed impedance, or whether a trap or fan arrangement leaves a strange pattern, a model gets you the answer before you have wire in the air.

One practical habit for both MMANA and EZNEC: model your measured antenna after you build it. If the model resonates a few percent away from the real one, adjust the ground or wire height assumptions until they line up. Once they match, you can trust the model more for the next change. Also keep segment count consistent when you compare two designs, otherwise the comparison can be dominated by numerical differences, not by the antenna.

For verticals specifically, treat model results with some caution. Radial-field loss and nearby objects are hard to represent, so use it for relative comparisons, and rely on field measurements for the final tune.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.