Stuck between 5 and 20 WPM: what actually moves the needle (plateaus, head copy, drills, nets, keyer setup)?
- Replies 2
- Views 32
- Created
- Last Reply
Top Posters In This Topic
-
Admin_Terry 1 post
-
Mod_Chrissy 1 post
I'd like to collect practical advice on the 5 to 20 WPM stretch, since most of the common questions seem to land here: why progress stalls, how to get off pencil-and-paper copy, and whether to trust a decoder. Here is the framework I'd start from, and I'd like to hear where people disagree.
Character speed first. The usual advice is to learn characters at a real sending speed of around 18 to 20 WPM and stretch the spacing between characters and words, rather than slowing the characters themselves down. This is the Farnsworth idea. A dit at 20 WPM is about 60 ms, while at 5 WPM it is 240 ms. If you learn the 5 WPM sound, every character is a long melody you have to count, and that habit is hard to unlearn later. The Koch method follows the same logic: start with two characters at full speed and add one at a time once you copy about 90 percent of a session.
Plateaus. Two seem common. One shows up around 10 to 13 WPM, where you can no longer count dits and dahs and must recognize the whole character as a sound. The other shows up in the high teens, where copying letter by letter costs you more and more, and you have to start hearing whole words and common prefixes. Both usually respond to the same fix: practice a bit above your comfortable speed, accept some missed characters, and don't stop to puzzle over a miss. Dwelling on one dropped letter usually costs you the next three or four.
Head copy. It tends to come in stages. Start with short, very common words (the, and, you, name, rig, antenna) and say them silently as they arrive. Then move to callsigns and short exchanges like RST, name, and QTH, then to full phrases. Writing everything down isn't wrong, but if you only ever write, your brain stays in character-by-character mode. A decent compromise is to write only the callsign and numbers during practice QSOs and let the rest go by in your head.
Drills. Random-character drills build raw recognition. Word and callsign drills build the pattern-matching you actually use on the air. Callsigns are useful because they are short, irregular, and carry real stakes in a contest or pileup. Programs like Morse Runner simulate pileups and let you adjust speed and noise. Spend a short block of each session on callsigns only.
Keyer and paddles. Poor sending can hold back your copying more than people expect, because you learn to hear your own mistakes. Set the keyer speed to a pace you can send cleanly, not the fastest you can hit. Keep weight near the default (about 3:1 dah-to-dit) until your timing is solid. Sidetone pitch is personal, but somewhere in the 500 to 700 Hz range is a common comfortable choice. Keep paddle spacing and tension light enough that you aren't fighting the paddle at speed. Iambic A and B differ in whether the keyer adds a final element when you release both paddles. Try both, and use whichever matches your hand rather than whichever someone says is better.
Ear versus software. A decoder is fine for checking your copy afterwards and for confirming a callsign. As a primary tool it has real limits. Fading, noise, QRM, and irregular spacing (many operators have a distinctive fist) can all produce garbage. If you always glance at the screen, you also won't develop the skill you are trying to build. A reasonable rule: copy by ear first, then check with software only after the fact.
Schedule. Short daily sessions of 15 to 30 minutes usually beat one long weekly session, especially because the skill consolidates between sessions. A sample week might mix new-character or speed-push drills, callsign practice, listening to real on-air CW, and one low-pressure QSO or net check-in. Rest days are fine.
Getting on the air. Slow-speed CW nets and structured events like short timed contest sessions can bridge the gap between drills and real operating. Contests are good for speed building because the exchange is predictable, so you learn to copy the parts that matter. Starting by only answering stations calling CQ at your speed, and sending a standard exchange, lowers the pressure.
So what's worked best for you at each stage, and what advice do you think is overrated?
Link to comment
https://www.hamradiobase.com/forums/topic/11244-stuck-between-5-and-20-wpm-what-actually-moves-the-needle-plateaus-head-copy-drills-nets-keyer-setup/Share on other sites