Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Dual-band mobile rigs compared: FTM-500D, ID-5100A and TM-D710G, plus wiring, noise and etiquette

ci_cover.jpg

Many people putting a 2 meter / 70 centimeter radio in a vehicle are choosing between three well-known 50-watt class dual-band mobiles: the Yaesu FTM-500D, the Icom ID-5100A and the Kenwood TM-D710G. They overlap a lot, but they lean toward different kinds of operating. This thread is for comparing them and for the less glamorous parts of a good mobile: power wiring, fusing, antenna mounting, noise and on-air manners.

Starting points for discussion:

Which radio fits which style. The FTM-500D is built around Yaesu's C4FM digital mode with analog FM, and it is the one to look at if your local repeaters or WIRES-X rooms use that system. The ID-5100A is the D-STAR choice, with a large touchscreen and a focus on digital voice and GPS-linked features. The TM-D710G is an analog FM radio with built-in APRS and a TNC, which makes it attractive if you want position reporting and messaging without an external tracker. Before choosing on specs, find out which modes your local repeaters actually use. A radio with a mode nobody around you uses is just an expensive analog rig.

Cross-band repeat. Among these three, the TM-D710G is the one commonly associated with a cross-band repeat function, which lets you use a handheld on one band and have the mobile retransmit on the other. Check the manual for your exact model and firmware before counting on this for any of them. Also remember that you are still the control operator. Know your licence class privileges, ID properly, and don't leave a cross-band repeat running unattended where it could cause interference.

Power and fusing. A 50-watt FM mobile can pull on the order of 10 to 12 amps or more on high power transmit, so the cigarette-lighter socket is the wrong source. The supplied power cable normally has fuses in line on the positive lead, and those fuses belong close to the battery, not near the radio. If you extend the cable, use wire at least as heavy as the original, keep joints crimped and soldered or otherwise properly made, and don't replace a fuse with a larger one just to stop it blowing. A blown fuse is telling you something. On newer vehicles, especially ones with battery current sensors or start-stop systems, check the manufacturer's guidance on where to connect the negative lead. Hybrids and EVs have their own 12 V access points and cautions.

Mounting. The radio body needs a secure spot where it won't become a projectile or block airbag deployment. The control head or face should be where you can see it without taking your eyes off the road for more than a glance. Leave air space around the heat sink or rear fan area. The microphone should have a clip or holder, and the cable should be routed where it can't snag the pedals or shifter.

Antenna and noise. A good antenna usually matters more than the choice between these radios. A roof-center NMO mount with a quality dual-band whip generally outperforms a trunk-lip or glass-mount setup, and SWR should be checked on both bands. Typical mobile noise sources include alternator whine, ignition and injector noise, LED lighting, USB chargers and DC-DC converters. On FM you may hear it as a need to raise the squelch or as whine in your transmitted audio. Routing the power cable away from the engine bay wiring harness, keeping it short and using ferrite chokes where they help are all common first steps. Isolate noise by unplugging or turning off accessories one at a time.

Etiquette. Listen before you transmit, especially if you use dual watch on a couple of repeaters. Keep transmissions short, give your callsign properly and don't treat the repeater as a private chat room while driving. Whatever your local law says about hands-free operation, keep your attention on the road. A voice command, a steering wheel PTT or just staying quiet in heavy traffic is better than fumbling with a touchscreen.

What have you found worth planning before the first drill hole goes in?

  • Replies 2
  • Views 32
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

On wiring, one thing that often gets skipped is where the ground goes. Running power straight to the battery is the usual advice for the positive lead, but the negative is the part where modern vehicles need extra thought. If the car has a battery monitoring sensor on the negative terminal, check the vehicle's service information before attaching anything to the post, because the usual practice is to follow the manufacturer's recommended ground point rather than bypass the sensor.

On fuse placement, remember the main rule: the fuse protects the wire, so it sits as close to the power source as practical. If the supplied radio cable is lengthened, the extension should be at least the same gauge. Also check voltage drop under transmit load. A radio that behaves oddly at 50 W but fine at low power often has a poor connection or undersized wire somewhere in the run.

Don't forget strain relief and grommets where the cable passes through the firewall. A sharp edge against copper insulation is how a fuse upstream ends up being the only thing between the cable and a short.

  • Administrators

On the radio choice, I'd start from the local repeater list rather than from the spec sheet. If the area is mostly analog FM, the TM-D710G is a practical match, and its APRS and cross-band features are the reason people pick it. If the busiest nets or rooms near you are on D-STAR or C4FM, the ID-5100A or FTM-500D respectively makes more sense. Digital modes only pay off when there are people on them to talk to.

For noise, a useful method is to do it in steps. Check the radio with the engine off, then with the ignition on, then running, then with the HVAC, wipers and lights on. Whatever changes the noise tells you where it comes from. Alternator whine that follows engine RPM points to power-lead filtering or routing. Hash that appears with a certain accessory points to that accessory, and the fix is often moving a charger or LED light, not the radio.

Also test SWR before blaming the radio for poor range. A mount with a bad ground connection or a damaged coax end can make a good radio sound weak, and it's easy to overlook on UHF where losses and poor connections show up faster.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.