ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
Dead rig triage: a sensible order for no TX, no RX, protection faults and blown finals
This thread is for sorting out the order of checks when a rig arrives on the bench with a vague complaint like "it's dead" or "it receives but won't transmit." Most wasted repair time comes from jumping to the finals or the alignment slugs before confirming the boring things. Here is a starting framework, and please correct or add to it.
1. Power first, and measure it where the rig sees it. Check voltage at the rig's DC connector, not at the supply terminals, and check it again during transmit. A supply that reads 13.8 V unloaded can sag badly through a tired fuse holder, a corroded Anderson or Powerpole contact, or thin cable. Many rigs will mute, reset, or fold back power when the input drops. Also look at the supply output with a scope if you have one. A failing switch-mode supply can show a healthy DC reading on a DMM while carrying enough ripple and spikes to upset the receiver and the PLL.
2. No transmit and no receive at the same time usually points to something common to both. That means the main regulators (the 8 V, 5 V and 3.3 V rails, depending on the design), the reference oscillator, a PLL that isn't locking, or the CPU not booting. The service manual's block diagram and voltage table are worth more than any generic advice here. Check the regulated rails first, then the reference oscillator, then the PLL lock voltage or lock-detect line. A rig with a dead display and no response to the controls often has a dead logic rail before it has any RF problem.
3. Receive only. Signal-trace from the antenna jack toward the speaker. An RF signal generator and a scope or RF probe let you inject at a known level and see where the signal disappears. Common culprits are the antenna changeover relay, band-pass filter relays, PIN-diode switching, a dead mixer or IF filter, or a bad AF stage. Dirty relay contacts and oxidised switch or pot contacts cause intermittent behaviour more often than outright part failure. Use a cleaner made for electronics, use it sparingly, and don't flood things you can't rinse.
4. Transmit only, or low and no output. Work from the exciter forward. Is there drive at the driver input? Is the driver biased? Is there DC on the final stage? Then look at the control side: ALC, power-control loops, and the protection circuit. Do all of this into a dummy load, never into an open connector.
5. SWR protection faults. If a rig folds back or shows a high-SWR warning, first confirm it with a dummy load. If the fault disappears, suspect the antenna, coax, or a connector. If it stays with a known-good dummy load, the fault is inside the rig: the directional coupler or SWR bridge, its detector diodes, the sense amplifier, or the lowpass filter relay network. A shorted or leaky detector diode can fake a high reflected-power reading and trip protection with a perfectly good load.
6. Blown finals. Replacing the transistors is the easy part, and the real question is why they died. Typical causes include a high-SWR event with failed protection, overdrive from a faulty ALC, a supply running over-voltage, a parasitic oscillation, failed bias components, or a bad driver. Before powering up new devices, check the bias network, the emitter or source resistors, any bias thermistor or diode, and the output transformer and its components. Fit the correct matched devices, use a current-limited bench supply or a series lamp where practical, set idle current per the service manual with a dummy load connected, and bring the drive up slowly.
7. Capacitors, noise, and alignment. Electrolytics in older gear often dry out, and leaking SMD electrolytics can damage nearby traces. When replacing, match capacitance, use an equal or higher voltage rating and a suitable temperature rating, and watch polarity. Low-ESR types are right for supply decoupling and switching regulators, but follow the original design where it matters. For noise, compare a battery or a known-quiet supply against the normal one, terminate the antenna jack with a dummy load to separate internal noise from external noise, and look at the supply rails with a scope. Leave alignment until after the repair is done. If a rig only needed a cleaned relay or a replaced capacitor, tweaking slugs and trimmers can make things worse. When alignment is actually needed, follow the service manual's procedure with a signal generator, frequency counter, RF power meter and dummy load.
Tools worth having: a decent DMM, a bench supply with current limiting, a dummy load and wattmeter, an RF probe, and a scope. A modest scope covers supply ripple, audio, bias lines, and clock signals. Seeing RF directly needs more bandwidth and a good probe. An ESR meter, a signal generator, and a NanoVNA for checking filters and matching are useful extras. Always take mains and high-voltage safety seriously, especially in tube equipment, and discharge big capacitors before you reach in.
What order do you work in, and which one check do you do first that most people skip?
This thread is for sorting out the order of checks when a rig arrives on the bench with a vague complaint like "it's dead" or "it receives but won't transmit." Most wasted repair time comes from jumping to the finals or the alignment slugs before confirming the boring things. Here is a starting framework, and please correct or add to it.
1. Power first, and measure it where the rig sees it. Check voltage at the rig's DC connector, not at the supply terminals, and check it again during transmit. A supply that reads 13.8 V unloaded can sag badly through a tired fuse holder, a corroded Anderson or Powerpole contact, or thin cable. Many rigs will mute, reset, or fold back power when the input drops. Also look at the supply output with a scope if you have one. A failing switch-mode supply can show a healthy DC reading on a DMM while carrying enough ripple and spikes to upset the receiver and the PLL.
2. No transmit and no receive at the same time usually points to something common to both. That means the main regulators (the 8 V, 5 V and 3.3 V rails, depending on the design), the reference oscillator, a PLL that isn't locking, or the CPU not booting. The service manual's block diagram and voltage table are worth more than any generic advice here. Check the regulated rails first, then the reference oscillator, then the PLL lock voltage or lock-detect line. A rig with a dead display and no response to the controls often has a dead logic rail before it has any RF problem.
3. Receive only. Signal-trace from the antenna jack toward the speaker. An RF signal generator and a scope or RF probe let you inject at a known level and see where the signal disappears. Common culprits are the antenna changeover relay, band-pass filter relays, PIN-diode switching, a dead mixer or IF filter, or a bad AF stage. Dirty relay contacts and oxidised switch or pot contacts cause intermittent behaviour more often than outright part failure. Use a cleaner made for electronics, use it sparingly, and don't flood things you can't rinse.
4. Transmit only, or low and no output. Work from the exciter forward. Is there drive at the driver input? Is the driver biased? Is there DC on the final stage? Then look at the control side: ALC, power-control loops, and the protection circuit. Do all of this into a dummy load, never into an open connector.
5. SWR protection faults. If a rig folds back or shows a high-SWR warning, first confirm it with a dummy load. If the fault disappears, suspect the antenna, coax, or a connector. If it stays with a known-good dummy load, the fault is inside the rig: the directional coupler or SWR bridge, its detector diodes, the sense amplifier, or the lowpass filter relay network. A shorted or leaky detector diode can fake a high reflected-power reading and trip protection with a perfectly good load.
6. Blown finals. Replacing the transistors is the easy part, and the real question is why they died. Typical causes include a high-SWR event with failed protection, overdrive from a faulty ALC, a supply running over-voltage, a parasitic oscillation, failed bias components, or a bad driver. Before powering up new devices, check the bias network, the emitter or source resistors, any bias thermistor or diode, and the output transformer and its components. Fit the correct matched devices, use a current-limited bench supply or a series lamp where practical, set idle current per the service manual with a dummy load connected, and bring the drive up slowly.
7. Capacitors, noise, and alignment. Electrolytics in older gear often dry out, and leaking SMD electrolytics can damage nearby traces. When replacing, match capacitance, use an equal or higher voltage rating and a suitable temperature rating, and watch polarity. Low-ESR types are right for supply decoupling and switching regulators, but follow the original design where it matters. For noise, compare a battery or a known-quiet supply against the normal one, terminate the antenna jack with a dummy load to separate internal noise from external noise, and look at the supply rails with a scope. Leave alignment until after the repair is done. If a rig only needed a cleaned relay or a replaced capacitor, tweaking slugs and trimmers can make things worse. When alignment is actually needed, follow the service manual's procedure with a signal generator, frequency counter, RF power meter and dummy load.
Tools worth having: a decent DMM, a bench supply with current limiting, a dummy load and wattmeter, an RF probe, and a scope. A modest scope covers supply ripple, audio, bias lines, and clock signals. Seeing RF directly needs more bandwidth and a good probe. An ESR meter, a signal generator, and a NanoVNA for checking filters and matching are useful extras. Always take mains and high-voltage safety seriously, especially in tube equipment, and discharge big capacitors before you reach in.
What order do you work in, and which one check do you do first that most people skip?
Link to comment
https://www.hamradiobase.com/forums/topic/11256-dead-rig-triage-a-sensible-order-for-no-tx-no-rx-protection-faults-and-blown-finals/Share on other sites