Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Indices vs. real-time evidence: how do you decide which band to check for DX?

ci_cover.jpg

There are two ways to approach HF and VHF conditions. One is to read the numbers: SFI, A index, K index, and the sunspot number. The other is to look at what is actually being received right now through WSPR, beacons, and spotting networks. Both are useful, but they answer different questions, and mixing them up leads to a lot of wasted time at the radio.

As a rough guide, the 10.7 cm solar flux (SFI) tracks the ionizing output of the sun, so it correlates with F-layer ionization and the maximum usable frequency (MUF). Very low flux means 15m, 12m, and 10m will often be dead except for brief or localized openings. Higher flux makes F2 propagation on those bands far more likely. The A index is a daily summary of geomagnetic disturbance, and the K index is a 3-hour snapshot on a 0 to 9 scale. High values usually hurt paths that cross the polar regions. They can also depress the F layer, though effects vary with season and location.

The catch is that none of these numbers tell you whether you can work a specific station in a specific place in the next twenty minutes. A decent SFI with a quiet K index can still give a poor path if the gray line has moved away or the D layer is absorbing your signal on 40m during the day. Likewise, sporadic E can open 10m, 6m, or even 2m with no help from the SFI.

So here is my question for the group. What is your workflow for deciding where to look? Do you start with the indices and a prediction tool like VOACAP, or do you go straight to WSPR and beacon activity? And how do you handle the VHF side, where tropospheric ducting and sporadic E follow rules that have little to do with the sunspot cycle?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I would treat the indices as a filter, not a forecast. SFI and the sunspot cycle tell you what the upper bands can potentially do. A and K tell you whether the ionosphere is currently disturbed. After that, think about the layers. The D layer exists mainly in daylight and soaks up energy at lower HF frequencies, which is why 160m and 80m are generally poor for long-distance work in the daytime and improve after sunset. A solar flare can add a sudden burst of D-layer absorption on the sunlit side of the Earth, so a band can fade out abruptly even when the long-term numbers look fine.

The F layer is what supports long-distance DX. Your highest workable frequency on a path is limited by the MUF, and it shifts through the day, season, and solar cycle. When the MUF drops below a band's frequency, the band closes for that path. When it sits comfortably above, you may get good signals, though absorption and noise still matter.

The gray line is a real effect to use. Around sunrise and sunset, the D layer is weak at one end of the path while the F layer is still usable. That is why the lower bands often show interesting openings along the terminator, especially on 40m, 80m, and 160m. It is not magic, but it is a good time to listen.

On NVIS, the logic is different. For regional coverage out to a few hundred kilometers, you want high-angle radiation and a frequency below the critical frequency of the F layer at that time. In practice that usually means 40m or 60m in the daytime and 80m or 160m at night, depending on conditions. Going too high means your signal punches through the layer, and going too low means more D-layer absorption in the daytime. A low dipole, such as one at a fraction of a wavelength above ground, tends to help NVIS because it sends more energy upward.

  • Moderators

For checking the band in real time, the most useful habit is to stop guessing and look at spots. WSPR is great for this because it works at very low power and reports signal-to-noise ratio. You can transmit on a band for a few cycles, see which stations decode you, and then compare to a spotting map. Remember that WSPR shows where receivers are, not where every possible path is. A station-poor region can look dead on the map even when the band is open. SNR reports are also referenced to a specific noise bandwidth, so they do not translate directly to what you will hear on SSB. Use them as a relative indicator of whether a path exists.

Beacons help in a similar way. The NCDXF/IARU beacon network on 14.100, 18.110, 21.150, 24.930, and 28.200 MHz uses a repeating 3-minute schedule. Each beacon sends its call sign and a series of tones at 100 W, then 10 W, 1 W, and 0.1 W. If you can hear the 1 W step from a beacon, the path is strong. Hearing only the 100 W step means the opening is marginal. There are also beacons on 6m and other VHF bands that can alert you to sporadic E or tropo openings. For CW and digital modes, the Reverse Beacon Network and PSKReporter can show you where you are being heard.

VOACAP and similar tools fit in as planning aids. They use a monthly smoothed sunspot number, your antenna and power assumptions, and the path to estimate when each band is likely to work, along with predicted reliability and SNR. That makes them useful for deciding what to try at what time of day. They are not a day-by-day forecast, so a quiet-looking prediction can be wrong during a disturbed day, and a poor prediction can be wrong during an unusual opening.

For VHF, tropospheric ducting is mostly a weather story. Temperature inversions and stable high-pressure conditions, especially over water or flat terrain, can trap signals and extend 144 MHz and higher paths well beyond line of sight. Sporadic E is separate. It occurs in patches of dense ionization in the E layer, with a strong seasonal peak around early summer and a smaller one in midwinter in the northern hemisphere. Neither depends on SFI, so for those openings, watching beacons, spotting clusters, and local weather data tends to be more useful than the solar numbers.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.