Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bring-up order for a first homebrew QRP transmitter: what to check before an antenna goes on

ci_cover.jpg

Kit-built and scratch-built QRP rigs, from a Tuna Tin 2 style crystal oscillator transmitter to a Pixie or a BITX/uBITX transceiver, tend to fail in the same few ways. They don't fail because the circuit is exotic. They fail because nobody checked the basics in a sensible order. I'd like to collect a bring-up sequence that works for most small builds, and hear where people would change it.

Here is my starting point. First, inspect the board before power goes on: solder bridges, cold joints, polarity of electrolytics and diodes, transistor pinouts (a 2N2222 in a metal TO-18 can is not pinned like a plastic TO-92 part), and toroid winding counts. A good light and a magnifier find more faults than any instrument.

Second, power it from a current-limited bench supply, or from a normal supply with a resistor in series with the positive lead. Start with the limit set a bit above the expected idle current. A receiver or an unkeyed transmitter drawing several times its expected current is telling you something right away. Add a reverse-polarity diode or a fuse if the design doesn't have one.

Third, check DC conditions stage by stage before looking at RF. Measure bias voltages, regulator outputs, and the supply voltage at the PA. Then confirm the oscillator is on frequency with a counter, a scope, or a nearby receiver. For crystal oscillators, check that it starts reliably every time you key it, not just once.

Fourth, put the transmitter into a 50 ohm dummy load, never an antenna. Measure output with an RF probe or a scope across the load. Power in a resistive load is P = Vpp² / (8 × R), so 10 V peak-to-peak into 50 ohms is 0.25 W. That is about the range a Tuna Tin 2 style circuit aims for, so it makes a convenient sanity check.

Fifth, look at the harmonics before going on the air. Simple single-transistor transmitters, and the Pixie in particular, rely heavily on the output network for harmonic suppression. A low-pass filter is not optional. If you can, use a spectrum analyzer with an attenuator in front of it, or listen on a second receiver at two and three times the operating frequency. Never connect a transmitter output directly to an analyzer or counter input without attenuation.

Last, check keying. Look at the keyed waveform on a scope or listen on a monitor receiver. Hard-keyed oscillators and PAs can produce key clicks that spread far beyond the signal. A small RC or an R-L-C shaping network in the keying line is often enough.

What would you reorder or add? And for those building direct conversion receivers, is there a similar checklist for the audio chain, the product detector, and the local oscillator leakage?

  • Replies 2
  • Views 29
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

That order is sound. The one thing I'd add is measuring the dummy load itself. A cheap resistor load can be quite reactive at higher HF, and a homemade one built from a few carbon film resistors may look fine on 80 m and wrong on 10 m. If you have an antenna analyzer or a NanoVNA, check the load's SWR across the band you intend to use. Otherwise your power and harmonic readings carry an error you don't know about.

For the power calculation, make sure your probe is rated for the voltage and the frequency. A simple diode probe with a DMM reads low at small signals because of the diode forward drop, and it reads peak or near-peak, not RMS. So it's best calibrated against a known source or checked with a scope. This matters a lot at QRP levels. The same goes for a homemade SWR bridge. Diode detectors are non-linear at low power, so a reading that looks like a perfect null on 5 W may behave differently at 500 mW. Check the null with a plain 50 ohm resistor, then with a deliberately mismatched load such as 100 ohms (SWR 2:1) and 25 ohms (also 2:1), and see whether the readings agree.

  • Administrators

On the direct conversion side, I'd split the checklist into audio first, RF second. Get the audio amplifier working before the mixer goes in: a finger touched to the input should produce hum, and the gain should be stable without motorboating. Many DC receivers go wrong because the supply isn't decoupled enough between the high-gain audio stages and the LO, and a bit of extra capacitance and a series resistor on the supply line fixes a lot.

Then bring in the product detector and the VFO. Common problems are LO leakage radiating from the antenna, AM broadcast breakthrough because there is no front-end filter, and hum or microphonics caused by a drifting or poorly shielded VFO. A bandpass filter at the input and a bit of buffering after the oscillator help a lot. If it is a single-signal build, check opposite-sideband rejection with a signal generator, or with a nearby transmitter into a dummy load, by tuning on each side of zero beat and comparing the levels.

For the BITX/uBITX crowd, the same discipline applies. Don't rely on the factory output filters being correct just because the board is assembled. Check the output on a scope and an analyzer on each band, and be cautious about running it at its highest drive level into a real antenna until you've seen the spectrum.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.