Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Where does your SDR noise floor actually come from? Dynamic range, upconverters and antennas for HF through VHF

ci_cover.jpg

A lot of SDR buying and troubleshooting threads come down to one confusion: people treat sensitivity, dynamic range and antenna noise as the same thing. They are different limits, and which one you hit depends on the band. This thread is meant to lay out the pieces and compare approaches, so corrections are welcome.

ADC bits and what they buy you. The ideal SNR of an N-bit converter is roughly 6.02N + 1.76 dB. For 8 bits that is about 50 dB, for 12 bits about 74 dB, and for 14 bits about 86 dB. Real devices fall short of these figures because of ADC non-linearity, tuner noise and gain-stage compromises. That number applies across the whole sampled bandwidth. Narrowing the bandwidth with decimation and filtering gives processing gain, so a 2.4 MS/s capture analysed with a 500 Hz resolution bandwidth looks much quieter than the raw bit depth suggests. Weak signals are not what overloads an 8-bit dongle. The problem is a strong FM broadcast, medium-wave or pager signal inside the sampled window, which forces the gain down or produces intermodulation products that look like real signals.

The hardware families, roughly. The RTL-SDR (RTL2832U plus an R820T2-type tuner) is an 8-bit device that covers roughly 24 MHz to 1.7 GHz, with a stable bandwidth of about 2.4 MHz. It is excellent value for VHF/UHF work such as ADS-B, APRS, weather satellites and 433 MHz sensors. HackRF One covers 1 MHz to 6 GHz, is half-duplex, and is also 8-bit. Its strength is the huge frequency range and TX capability, not weak-signal HF reception. SDRplay RSP units and the Airspy range are the usual step up for receive. They use higher-resolution converters, cover down to the LF/HF range (the Airspy HF+ line is specifically tuned for HF and low VHF), and have built-in filtering. SDRplay also offers selectable notch filters and switchable bandpass filtering on some models. LimeSDR is a wideband transceiver with 12-bit converters and full duplex, and it suits experimenters more than casual listeners.

Upconverters versus direct sampling. Dongles whose tuners start around 24 MHz can reach HF in two ways. Direct sampling feeds the ADC without the tuner. It is simple and cheap, but it has no real preselection, so you need a low-pass filter before the input to limit aliasing and out-of-band signals. An upconverter mixes HF up by a fixed local-oscillator offset, commonly 100 or 125 MHz in popular designs, so that 0 to 30 MHz appears at 125 to 155 MHz. You then set a frequency offset or shift in the software so the display still reads the true frequency. Upconverters add a mixer and LO to the chain, so watch for LO leakage, spurs and images, and make sure a proper low-pass filter sits ahead of the mixer. Neither approach fixes the 8-bit limit.

Noise. On HF, especially below about 20 MHz, the limiting noise is usually external: man-made noise, switch-mode supplies, LED lighting, powerline noise and local computers. A very quiet receiver will not improve a noisy antenna site. A quick test is to connect the antenna and see whether the noise floor rises noticeably above what you see with a dummy load. If it rises clearly, you are external-noise-limited and more receiver sensitivity is unlikely to help. If it barely moves, the receiver front end is limiting, and a low-noise preamp or a better antenna may help. On VHF/UHF the situation is different, and feedline loss and the receiver's own noise figure matter more, so a masthead LNA can make a real difference.

Antennas. Small active E-field whips and loops can be useful where space is limited, but they can overload on strong signals and pick up noise from the feedline. A common-mode choke at the receiver end is a cheap first step against noise riding on the coax. A magnetic loop can reject some local electrical noise. A random wire with a 9:1 unun is broadband but picks up whatever is nearby. For VHF/UHF, a discone gives wide coverage for scanning, while a tuned dipole, V-dipole or ground plane usually performs better on one band, such as 137 MHz weather satellites or 1090 MHz ADS-B.

Software. SDR# is a popular Windows option with a plugin ecosystem. SDRuno is the SDRplay-focused Windows application with detailed multi-VFO and filtering controls. HDSDR is a Windows front end that uses ExtIO drivers and can be driven through OmniRig for CAT use. GQRX runs on Linux and macOS and is built on GNU Radio. CubicSDR is cross-platform and works through SoapySDR, which suits less common hardware. For digital modes, the usual approach is to route demodulated audio through a virtual audio cable into a decoder, for example WSJT-X for FT8, multimon-ng for POCSAG, or direwolf for APRS. The decoder cares about correct filter width, mode and a clean audio level, so check those before suspecting the decoder.

Questions for discussion: for people working on HF with a budget around an RTL-SDR, is direct sampling with a good filter or an upconverter the better first step? And for panadapter use, where do you tap the signal, and how do you protect the SDR front end during transmit?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

One thing to add to the gain discussion is that the right gain setting is rarely the maximum. A practical method is to watch the spectrum while raising the gain. The noise floor should come up a little above the dummy-load level, but if strong signals start producing spurs that move in the wrong direction when you change the gain, or you see a lot of symmetrical junk around a strong carrier, you are probably overloading the front end. At that point, adding gain only makes things worse. A broadcast FM band-stop filter and a medium-wave high-pass or band-stop filter are often the most cost-effective improvements on a dongle. They remove the strongest signals before the tuner and ADC, so the AGC and gain controls don't have to back off for them.

On the antenna side, noise from nearby electronics can enter through the coax shield as common-mode current, not through the antenna itself. If the noise changes when you move or touch the feedline, a choke made from a few turns of coax on a suitable ferrite core is worth trying. For active whips, the bias tee supply can be a noise source itself, particularly if it is powered from a noisy USB port or laptop, so try a separate clean supply or a ferrite-isolated USB cable before blaming the antenna.

  • Moderators

On the direct sampling versus upconverter question, the answer depends on what you want to hear. Direct sampling on an RTL-SDR gives an HF-capable receiver with few parts, but it is an 8-bit ADC with no preselection, so a few strong broadcast stations in the shortwave bands can limit what you can copy. An upconverter gives a cleaner frequency plan when it is well designed, but you have to account for the extra mixer, filters and LO, and the software offset has to be right. Either way, the receiver may not be the bottleneck. If the HF antenna is noisy, you may gain more by moving it than by changing hardware. For HF-focused listening, receivers designed for LF/HF, such as the Airspy HF+ family and the SDRplay RSP range with its HF filtering, usually give better results than an 8-bit dongle with a converter.

For panadapter use, the usual choices are an IF tap, if your transceiver has one, or a low-level sample of the antenna signal through a splitter or coupler. In both cases the SDR should never see transmit power. Use an SDR input that is protected or switched out during transmit, or a dedicated RX output, and don't rely on hoping a small attenuator will be enough. For software, CAT control through OmniRig in HDSDR or similar is mainly about keeping the SDR display frequency in step with the radio, and it does not change the signal path.

For decoding, if a mode is failing, work from the front end onward. Check that the SDR is not overloading, that the demodulator mode and bandwidth suit the signal, that the audio level into the decoder is sensible, and that the sample clock is accurate enough. A cheap dongle with poor frequency stability can drift enough to affect narrow digital modes, and a TCXO-equipped unit or a PPM correction can fix that.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.