Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Bench-testing a homebrew QRP transmitter before it touches an antenna: dummy load, scope, harmonics and what to check first

ci_cover.jpg

Simple transmitters like a Pixie, a Tuna Tin 2 style crystal oscillator and PA, a BITX-derived rig or a modified uBITX are easy to get running. They are also easy to put on the air with a dirty signal. A transmitter that makes contacts is not necessarily one that is clean, stable or properly keyed. This thread is a place to compare bench procedures that need little more than a dummy load, a scope and a multimeter.

A sensible order looks like this. First, power up from a current-limited supply with a diode or fuse in the line, and check the idle current against what the design predicts. Second, connect a 50 ohm dummy load before you key anything. Third, measure RF voltage across the load. With a 50 ohm load, power is roughly Vpp squared divided by 400, so 20 Vpp is about 1 W and 40 Vpp is about 4 W. This assumes a reasonably clean sine wave and a probe good enough for the frequency. Fourth, look at the waveform. A flat-topped, lumpy or visibly distorted sine on a scope means a lot of harmonic energy.

The low-pass filter is the part that gets skipped most often. A Pixie-style circuit, where the transmit stage also acts as the receive mixer, normally has nothing but a tuned circuit between the transistor and the antenna. A single-band Chebyshev low-pass filter of five or seven elements, wound on powdered-iron toroids such as T37-2 or T50-2 cores, is the usual cure. Even then, check it. Winding a turn too few or too many can move the cutoff enough to hurt the fundamental or leave the second harmonic too strong. A NanoVNA, a tinySA or a borrowed spectrum analyzer will show this far better than a scope trace. If you use a spectrum analyzer, put a proper attenuator in front of it so you do not damage the input.

Keying is the other thing worth checking on the scope. Look at the keyed envelope with the scope on the dummy load. A square-edged envelope produces key clicks that spread well beyond your signal. Rise and fall times of a few milliseconds, set by an RC network or a shaping transistor stage, are a common compromise for CW. A transmitter can have clean harmonics and still be a nuisance because of sharp keying.

What does your own pre-air checklist include? Do you rely on a scope and SWR bridge alone, or do you think a cheap VNA or spectrum analyzer is worth getting early, before more elaborate projects like amplifiers and filters?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

For most builders the first extra instrument worth buying is a way to see the spectrum, not a better scope. A scope tells you the waveform looks bad, but it will not tell you whether the second harmonic is 25 dB or 45 dB down. Many amateur regulators expect spurious emissions to be suppressed by something like 40 dB or more below the fundamental, depending on power and band, so check the actual rule in your own country rather than trusting a forum number. A tinySA or similar inexpensive analyzer with a 20 dB attenuator on the input makes that measurement possible. Remember that those cheap analyzers can have their own internal spurs, so confirm a suspicious peak by changing the input attenuation. If the spur level changes by the wrong amount, it is probably the analyzer, not your transmitter.

An SWR bridge is useful, but it is mostly an antenna tool. On the bench into a dummy load it will show a very low reflected reading, and that tells you little about harmonic content. A bridge also reads misleadingly if the transmitter is putting out harmonics, because a mismatch at harmonic frequencies can make the meter reading odd. I would treat it as a check on the antenna system after the transmitter is already proven clean.

One more bench habit that helps: run the transmitter from a supply with a current limit set a little above the expected draw. If a PA transistor goes into self-oscillation or a bias resistor is wrong, the limit gives you a chance to catch it before a part gets hot enough to fail.

  • Moderators

For BITX and uBITX builds the important point is that the design is a compact bidirectional SSB rig. Many of the same stages carry signal in both directions, so a small error in switching, grounding or filtering can show up in receive and transmit at the same time. The uBITX in particular uses a Si5351-based synthesizer controlled by an Arduino, and the clock outputs are square-wave sources. That means the mixing stages and the output filtering matter a lot. Builders have reported spurious products on some bands, so measure each band you plan to use rather than assuming the supplied low-pass filters are all equally good. Check the output on a dummy load with a spectrum analyzer if you can, and with a scope if you cannot.

On SSB rigs, drive level and linearity matter as much as the harmonics. Overdriving the microphone amplifier or the later stages produces splatter even if the low-pass filter is doing its job. A two-tone test using two audio oscillators or a computer sound card and a scope will show flat-topping and distortion in a way that a single whistle does not. If you do not have a scope, ask a nearby amateur with a decent receiver to listen and describe what they hear, but do that on a quiet frequency and with low power.

For CW-only projects such as Pixie or Tuna Tin 2 style transmitters, the equivalent concern is key clicks, as mentioned above, and chirp. Chirp usually comes from a VFO or oscillator being pulled when the PA keys on. A buffer stage, a stiffer supply for the oscillator, or a regulated 78L-series rail for the oscillator alone are common fixes. If the note sounds unstable on a nearby receiver, check the supply rail with the scope while keying before you start rewinding coils.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.