Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Planning a 100 W HF shack: PSU, tuner and amp order, whether a band-pass filter is worth it, and bonding

ci_cover.jpg

I'm sketching out a shack plan and want to sanity-check the order of operations before buying anything else. The rig shortlist is a 100 W class transceiver. The candidates are the IC-7300 or IC-7610, the FT-991A or FTDX10, the TS-590SG or TS-890S, and the K3S. A KX3 or Xiegu G90 would be the grab-and-go second radio. Rather than argue about which rig is best, I'd like to get the supporting infrastructure right, because that seems to cause more day-to-day grief than the radio itself.

These are the questions I'm stuck on.

1. Power. The 100 W rigs want 13.8 V DC and draw roughly 20 A or more on SSB/CW peaks at full power. How much headroom do you want in the supply, and does it matter whether it's linear or switch-mode? Is there a sensible way to handle DC cable gauge, fusing and distribution (Powerpoles, a fused distribution block) so voltage sag at the radio doesn't become a hidden problem? The KX3 and G90 are low power, so I assume they're much less fussy.

2. Signal chain. If I add an amplifier later, where does the antenna tuner go? Many of these rigs have an internal ATU, and there are also external tuners that sit after the amp. I also keep reading about band-pass filters. Are they something a single-operator station needs, or only for multi-radio setups where one transmitter desensitizes another receiver?

3. Grounding and bonding. This is the part I'm least sure of. I want to separate three things that get lumped together as "the ground": electrical safety (mains equipment grounds), lightning protection (entry panel, arrestors, ground rods bonded to the service ground), and RF behavior (common-mode current on feedlines, USB cables and power leads). What should I do first, and what is mostly myth?

On layout, my current thinking is to put the radio, tuner and any amp on one bench. I'd keep coax away from power and USB cables, run feedlines in through one entry point, and put a common-mode choke where the feedline enters the room. Is that a reasonable starting point, or am I missing something obvious?

  • Replies 2
  • Views 26
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Moderators

I'd split the grounding question the way you did, because each part has a different goal and a different fix.

Safety first. Every mains-powered piece of gear should be on properly grounded outlets, ideally on one circuit or power strip. That has nothing to do with RF. Lightning protection is a separate job. The usual principle is to give a strike a short, direct path outside the house and to bond everything to the same reference. That means the entry panel or arrestors, the ground rod(s) at the feedline entrance, and the electrical service ground should all be bonded together. Isolated rods that aren't tied to the service ground can create dangerous potential differences between them. Check your local electrical code and, for anything involving a tower or service panel, consider having a qualified electrician look at it.

The RF side is where the myths pile up. A long wire to a ground rod is not an RF ground at HF. At some frequencies it's a good radiator or a high-impedance stub. Most RF problems in a shack come from common-mode current on the outside of the coax, not from a missing earth connection. The more useful steps are a proper choke (ferrite or a coiled-coax choke sized for the band) at the feedline entrance, and another near the rig if you see RF feedback. Use a balun or unun that suits the antenna, and keep the antenna and feedline geometry symmetrical where it matters.

On the bench, a short bonding strap between the chassis of the rig, tuner and amp is cheap and sensible, because it keeps the equipment at the same RF potential. Don't expect it to fix a feedline that's carrying common-mode current. Also keep USB, CAT and audio cables short, and use ferrites (clamp-on or toroids with several turns) at both ends. Switch-mode supplies and some USB hubs are common noise sources on receive, so if the noise floor jumps, try unplugging things one at a time.

  • Moderators

On the signal chain and power, here is how I'd think about it.

Power supply: pick something rated clearly above the rig's peak current, so a 100 W rig usually wants a 25–30 A class supply rather than one that is only just adequate. That keeps it from running hot and holding the voltage under load. Linear and switch-mode both work. A good switch-mode unit is lighter and usually efficient, but a poor one can put noise on receive, so be ready to add ferrites or try a different supply if you hear birdies. Keep DC cables short and heavy enough for the current, fuse the positive lead close to the source, and use polarized connectors. Many radios will misbehave or reduce power if the voltage dips under transmit, so measure at the radio's connector while transmitting, not at the supply.

Tuner and amp: the order is normally transceiver, then amplifier, then external tuner, then feedline. The rig's internal ATU only matches the radio to whatever it sees, so it won't help the amp's output stage see a good load. If you run an amplifier, an external tuner after it is the proper way to present a low SWR to the amp output. If you use the internal tuner, tune at low power first, then switch on the amp. Follow the amp manual for drive level and ALC, since overdriving a solid-state amp is a good way to create splatter.

Band-pass filters: for one radio on one antenna, they are often not needed. They matter when two transmitters operate close together, as in SO2R or multi-op contest setups, or when a strong out-of-band signal (such as a nearby broadcaster) overloads the receiver. Direct-sampling and modern superhet rigs like the IC-7300, IC-7610, FTDX10, TS-890S and K3S usually have decent front-end performance for general use, though they differ in filtering approach. A BPF adds some insertion loss, and it has to be rated for the power level it sees. A filter in the wrong place can also present a poor impedance to an amp. I'd run the station without one first and add one only if you can identify a real interference problem.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.