ⓘ Callsign lookups are in real time via the FCC database.
Vanity callsign availability is refreshed daily at 6:00 AM CST.
The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cmvia PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHzDXSpotterInfo
Recent spots—
Select a band above to load spots
Ready — select a band to fetch live spots
SSB audio chain from mic to ALC: what actually helps a weak signal get through?
Most SSB audio problems come from the same few places: too much mic gain, too much processing, a poor mic position, or RF getting back into the audio path. Here is a rough order of work for tuning a voice signal, with a few open questions at the end.
Start with the microphone and the room. Mic choice matters less than how it is used. A dynamic mic or headset with a controlled response often works better on HF than a wide-range studio condenser, because the condenser also picks up room echo, fans and keyboard noise. Keep a consistent distance, usually a few finger-widths from your mouth. Speak slightly across the capsule rather than straight into it, and use a foam or pop filter to tame plosives. Because SSB only passes roughly 300 to 2700 Hz, extended highs and deep bass are wasted. Low-frequency thumps still eat into your power budget.
Set mic gain by ALC and peak power, not by feel. In SSB the mic gain sets drive level. The ALC meter is a warning that the rig is limiting that drive, so it should not be your target. As a general rule, speak at normal level with the processor off and adjust mic gain so ALC only touches the permitted zone on peaks. The exact zone varies by manufacturer and model, so check your rig's manual. Pinning ALC does not add useful talk power. It distorts the waveform, widens the signal with splatter, and makes you harder to copy. Also remember that SSB output is a peak-envelope measurement. Your average power is far lower than the wattage figure suggests, so watching the power meter on peaks and listening to the result tells you more than turning everything up.
Use the speech processor to raise average power, and use it sparingly. Compression, whether AF compression or an RF-based processor depending on the rig, reduces the gap between loud and quiet syllables so the average level rises. That can help in a pile-up or on a marginal path. Too much compression raises background noise, exaggerates sibilance and breath, and can sound harsh or pumped. Many operators keep compression modest, around the lower part of the rig's compression meter range. Beyond that, intelligibility often gets worse even though the signal looks stronger on the receiving S-meter. If your radio lets you adjust processor level separately from mic gain, re-check ALC after each change, because the two interact.
Use EQ to remove problems, not to add character. Cutting low frequencies below roughly 200 to 300 Hz often cleans up the transmitted signal. A small lift in the presence range around 2 to 3 kHz can improve intelligibility. Heavy boosts tend to make sibilants hiss and eat power that would otherwise carry vowels. Many rigs offer a TX bandwidth setting. A narrower setting, near 2.4 to 2.7 kHz, is considerate on crowded bands and often sounds fine. Wider settings can sound better on a quiet band during a casual chat, but wider is not better for weak-signal work, because more of your power goes into frequencies that add little to readability.
The monitor function is useful but limited. The monitor lets you hear your own audio, which is good for judging mic distance, room noise and basic tone. In many rigs, though, it taps the signal before the final RF stages, so it will not necessarily reveal splatter or IMD from overdriving the transmitter. For a truer picture, listen with a separate receiver, record yourself through an SDR, or use a remote receiver if one is within range. Ask for a candid report from someone you trust, and give them a specific list: clarity, distortion, bass boominess, and whether they hear splatter on adjacent frequencies when you speak.
Sideband convention and receive filtering. By convention, amateurs use LSB on 160, 80 and 40 meters and USB on 20 meters and above. On 60 meters, USB is the usual choice. Following the convention helps everyone tune in without hunting. For receive, a standard SSB filter of about 2.4 kHz is a good all-round starting point. When there is QRM, narrowing to 1.8 to 2.1 kHz can help, at some cost to voice quality. If your rig has IF shift or passband tuning, shift the filter away from the interfering signal before narrowing it further. A notch filter works well on carriers. Noise reduction can help on weak signals, but aggressive settings introduce watery artifacts that make speech harder to copy. Mind AGC too: a very fast AGC will pump on noise, and a slow one can hold down weak signals after a strong burst. Dial back RF gain or use the attenuator if the band is noisy and the preamp is only amplifying noise.
Working weak stations and DX. Tune accurately. A voice that sounds too high or too low and unnatural is probably off frequency, and a small tuning adjustment can bring back intelligibility. When calling DX, listen first to how the operator works: whether they are using split, how long their exchanges are, and whether they are calling by call-sign area or taking all comers. Keep calls short, send your callsign clearly in standard ITU phonetics, and do not repeat it more than necessary. Use only the power you need. Better audio discipline usually beats raising the ALC or speech-processor setting. If your signal is marginal, give a clear report and repeat key information once instead of talking continuously.
Don't ignore RF in the shack. If the audio sounds raspy, the meter jumps when you touch the mic, or the signal changes when you move cables, suspect RF feedback. Common fixes are ferrites on the mic and power cables, a proper station ground, a balanced antenna system or common-mode choke, and a reliable shield on the mic cable.
For discussion: what do you use as your target for ALC and compression settings on your rig? What EQ cuts have been most useful? And how do you check your audio objectively if you don't have a second receiver nearby?
Most SSB audio problems come from the same few places: too much mic gain, too much processing, a poor mic position, or RF getting back into the audio path. Here is a rough order of work for tuning a voice signal, with a few open questions at the end.
Start with the microphone and the room. Mic choice matters less than how it is used. A dynamic mic or headset with a controlled response often works better on HF than a wide-range studio condenser, because the condenser also picks up room echo, fans and keyboard noise. Keep a consistent distance, usually a few finger-widths from your mouth. Speak slightly across the capsule rather than straight into it, and use a foam or pop filter to tame plosives. Because SSB only passes roughly 300 to 2700 Hz, extended highs and deep bass are wasted. Low-frequency thumps still eat into your power budget.
Set mic gain by ALC and peak power, not by feel. In SSB the mic gain sets drive level. The ALC meter is a warning that the rig is limiting that drive, so it should not be your target. As a general rule, speak at normal level with the processor off and adjust mic gain so ALC only touches the permitted zone on peaks. The exact zone varies by manufacturer and model, so check your rig's manual. Pinning ALC does not add useful talk power. It distorts the waveform, widens the signal with splatter, and makes you harder to copy. Also remember that SSB output is a peak-envelope measurement. Your average power is far lower than the wattage figure suggests, so watching the power meter on peaks and listening to the result tells you more than turning everything up.
Use the speech processor to raise average power, and use it sparingly. Compression, whether AF compression or an RF-based processor depending on the rig, reduces the gap between loud and quiet syllables so the average level rises. That can help in a pile-up or on a marginal path. Too much compression raises background noise, exaggerates sibilance and breath, and can sound harsh or pumped. Many operators keep compression modest, around the lower part of the rig's compression meter range. Beyond that, intelligibility often gets worse even though the signal looks stronger on the receiving S-meter. If your radio lets you adjust processor level separately from mic gain, re-check ALC after each change, because the two interact.
Use EQ to remove problems, not to add character. Cutting low frequencies below roughly 200 to 300 Hz often cleans up the transmitted signal. A small lift in the presence range around 2 to 3 kHz can improve intelligibility. Heavy boosts tend to make sibilants hiss and eat power that would otherwise carry vowels. Many rigs offer a TX bandwidth setting. A narrower setting, near 2.4 to 2.7 kHz, is considerate on crowded bands and often sounds fine. Wider settings can sound better on a quiet band during a casual chat, but wider is not better for weak-signal work, because more of your power goes into frequencies that add little to readability.
The monitor function is useful but limited. The monitor lets you hear your own audio, which is good for judging mic distance, room noise and basic tone. In many rigs, though, it taps the signal before the final RF stages, so it will not necessarily reveal splatter or IMD from overdriving the transmitter. For a truer picture, listen with a separate receiver, record yourself through an SDR, or use a remote receiver if one is within range. Ask for a candid report from someone you trust, and give them a specific list: clarity, distortion, bass boominess, and whether they hear splatter on adjacent frequencies when you speak.
Sideband convention and receive filtering. By convention, amateurs use LSB on 160, 80 and 40 meters and USB on 20 meters and above. On 60 meters, USB is the usual choice. Following the convention helps everyone tune in without hunting. For receive, a standard SSB filter of about 2.4 kHz is a good all-round starting point. When there is QRM, narrowing to 1.8 to 2.1 kHz can help, at some cost to voice quality. If your rig has IF shift or passband tuning, shift the filter away from the interfering signal before narrowing it further. A notch filter works well on carriers. Noise reduction can help on weak signals, but aggressive settings introduce watery artifacts that make speech harder to copy. Mind AGC too: a very fast AGC will pump on noise, and a slow one can hold down weak signals after a strong burst. Dial back RF gain or use the attenuator if the band is noisy and the preamp is only amplifying noise.
Working weak stations and DX. Tune accurately. A voice that sounds too high or too low and unnatural is probably off frequency, and a small tuning adjustment can bring back intelligibility. When calling DX, listen first to how the operator works: whether they are using split, how long their exchanges are, and whether they are calling by call-sign area or taking all comers. Keep calls short, send your callsign clearly in standard ITU phonetics, and do not repeat it more than necessary. Use only the power you need. Better audio discipline usually beats raising the ALC or speech-processor setting. If your signal is marginal, give a clear report and repeat key information once instead of talking continuously.
Don't ignore RF in the shack. If the audio sounds raspy, the meter jumps when you touch the mic, or the signal changes when you move cables, suspect RF feedback. Common fixes are ferrites on the mic and power cables, a proper station ground, a balanced antenna system or common-mode choke, and a reliable shield on the mic cable.
For discussion: what do you use as your target for ALC and compression settings on your rig? What EQ cuts have been most useful? And how do you check your audio objectively if you don't have a second receiver nearby?
Link to comment
https://www.hamradiobase.com/forums/topic/11296-ssb-audio-chain-from-mic-to-alc-what-actually-helps-a-weak-signal-get-through/Share on other sites