Skip to content
View in the app

A better way to browse. Learn more.

Ham Radio Base

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.
Ham Radio Base — Education, Resources, Projects and Community
☀ Solar
SFI 99
SN 26
A 6
K 0 Quiet
X-Ray B2.3
Wind 384.8 km/s
Aurora 1
Updated 13:30 UTC HamQSL · N0NBH
Day 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor
Night 80/40m Good 30/20m Good 17/15m Fair 12/10m Poor

Callsign Lookup
_
Vanity Call Signs Available
Enter filters above and click Search.
ⓘ Callsign lookups are in real time via the FCC database. Vanity callsign availability is refreshed daily at 6:00 AM CST. The vanity search may be unavailable for a few minutes during this update.
Live DX spots
Live DX Spots — 70cm via PSKReporter · scroll or pinch to zoom
Band
Mode
Time
Loading map data…
MHz DX Spotter Info
Recent spots —
Select a band above to load spots
Ready — select a band to fetch live spots

Starting out with 5 W portable QRP: rigs, antennas and batteries that matter most

ci_cover.jpg

I'd like to collect some practical thinking on 5 W portable operation in one place. QRP threads tend to drift into "which rig is best", but the rig is often the smallest part of the decision. Here is how I'd break it down, and I'd like to hear where others disagree.

Power in perspective. Going from 5 W to 100 W is a 13 dB difference, a bit over two S-units if you count 6 dB per S-unit. That is real, but it is smaller than the swing between a poor antenna and a good one, or between a quiet site and a noisy one. Most QRP success comes from efficiency everywhere else in the chain: a resonant antenna, low-loss feedline, a clear takeoff, a good operating frequency and a good operator.

CW versus SSB. CW is the natural QRP mode. A narrow filter, or your own ears, gives a lot of effective gain, and the rigs can be tiny and frugal. Dedicated CW radios like the Mountain Topper series and the Penntek TR-35 are popular for summit and park activations because they are light and draw little current on receive. SSB at 5 W is workable, but it relies on a decent antenna and a not-too-crowded band. Multimode radios such as the Elecraft KX2 and KX3 cover both modes, and both can run above 5 W when power allows, so you can drop to QRP on purpose rather than because the radio forces you to.

Kits and building. Building is a big part of QRP culture. Hendricks QRP Kits has long offered kits aimed at portable and low-power use. At the very simple end is the Pixie, a minimalist CW transceiver in which one transistor stage does double duty. It is cheap and educational, but it has a wide, unselective receiver and very little output, so treat it as a learning project and a way to understand a transceiver block by block, not as a dependable DX radio. Whatever you build, plan on a low-pass filter you trust, and check your output on a meter or scope if you can.

Calling frequencies. The widely used QRP calling frequencies are around these (kHz): CW on 1810, 3560, 7030, 10106, 14060, 18096, 21060, 24906, 28060 and 50060; SSB on roughly 3985, 7285, 14285, 21385 and 28885. Treat these as meeting places, not reserved channels. Check your local band plan, since the legal segments differ by country and licence class. It is also good practice to call and then move off, so others can use the calling frequency.

QRP-ARCI. The QRP Amateur Radio Club International runs contests and awards aimed at low-power operators and publishes technical material. QRP in its contests is generally defined as 5 W output on CW or 10 W PEP on SSB, but always read the current rules for the event you are entering, as categories and power limits can vary.

Antennas. For portable work, the common choices are an end-fed half-wave with a matching transformer, a linked or multiband dipole on a light mast or tree branch, and an inverted V. An end-fed is quick to deploy, but it depends on a counterpoise and its losses depend on how well the transformer is built. A resonant dipole is less convenient, but it usually has the lowest loss. Keep the feedline short and the connectors clean, and don't give back with a lossy tuner what you gained at the antenna. Height and clearance help more than most clever tricks.

Power. Both LiFePO4 and lithium-ion packs suit portable QRP. A 4S LiFePO4 pack has a nominal voltage of about 12.8 V and charges to about 14.4-14.6 V, which is within some radios' limits and over others. Check your rig's maximum input voltage before connecting it. Put a fuse near the battery, use sensible connectors, and note that a pack with a battery management board is safer than a loose collection of cells. Small packs are often enough, as receive current for these radios is low, and the main limit is usually transmit current on long CQ sessions.

What's the first thing you'd tell someone planning a first portable QRP outing: radio, antenna, or power?

  • Replies 2
  • Views 33
  • Created
  • Last Reply

Top Posters In This Topic

Featured Replies

  • Administrators

I'd put the antenna first, and I'd say the first thing to get right is the plan for getting it up, not the antenna type. A wire that needs a 10 m throw into a tree is a poor choice if the site has no trees. A fixed-length mast and a simple inverted V may be better for open ground.

On end-fed halves: they are convenient, but the matching transformer and counterpoise are part of the antenna, not accessories. If the transformer core runs warm at 5 W, there is a mismatch or a core problem. A short run of coax or a choke at the feedpoint can also help keep RF off the rig and the operator.

On the radio side, one point for beginners is the receiver. At 5 W, you will be calling a lot of stations who don't hear you, so a rig with a good narrow CW filter makes it easier to pick out a weak reply. That is part of why compact CW rigs can feel better on the air than a simple kit with a wide, open receiver.

  • Moderators

For power, I'd add a note on voltage sag and cut-off. A radio with a minimum operating voltage may behave strangely, or drop output, when the battery gets low, and that can look like an antenna problem. Measure the battery voltage under transmit load if the radio has a meter, not just at rest.

LiFePO4 holds a fairly flat voltage through most of its discharge, which is nice for QRP, but it also means the voltage does not warn you before it falls off. A small voltmeter or a rig with a built-in readout gives you that missing warning. Also check the charger matches the chemistry. A charger meant for lead-acid or ordinary lithium-ion may not charge LiFePO4 correctly.

If you're deciding between a KX2/KX3 and a smaller CW rig, the question is how much you want to operate SSB or digital. If you only plan on CW, a smaller radio may save weight and money. If you'd like to try several modes, a multimode rig gives you more room to experiment. Either way, a decent log of what you worked with each antenna will tell you more than any spec sheet.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

Affiliate Disclosure: As an Amazon Associate, Ham Radio Base earns from qualifying purchases. Some links throughout this website may be affiliate links. If you purchase a product through one of these links, we may earn a commission at no additional cost to you. Your support helps us continue creating free articles, tutorials, reviews, and resources for the amateur radio community. N0TLB © Ham Radio Base - Powered by the Ham CQ DX Community. All rights reserved.

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.